[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
Search Results "Surface Hazard"
-
TRANSITION PLATE
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
106.5.76 Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
Rebuilding Together Grays Harbor - Aberdeen, WA
Many homes with kids were among the 3,180 in which RT volunteers upgraded electrical wiring in 2002, eliminating fire hazards and the risk of electrical shock....
-
EQUIVALENT FACILITATION
equivalent facilitation, consideration shall be given to means that provide for the maximum independence of persons with disabilities while presenting the least risk of harm, injury or other hazard...
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
102 Dimensions for Adults and Children
are also provided based on children’s dimensions and anthropometrics for drinking fountains, water closets and other elements located in toilet compartments, lavatories and sinks, dining surfaces...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
The Challenges EV Charging for People with Disabilities
Automatic cable management systems are ideal for public locations, as they: • Reduce liability from tripping hazards & false claims • Prevent damage to connectors from contact with...
-
Sec.36.403(c)(1)(ii)
(ii) Replacing an inaccessible floor surface in the customer service or employee work areas of a bank;...
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate FS 33538 of Federal Standard 595C....
