The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
Search Results "Door Surface"
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
-
Attachment I: Program Access in Existing Facilities
Attachment I: Program Access in Existing Facilities
-
HEWI System 111 Door Hardware
The hardware System 111 is modular and can therefore be aligned with individual requirements. A large selection of materials, colours, design variants and rose shapes and backplates...
-
HEWI Range 180 Door Hardware
Real materials lend Range 180 enhanced value. The lever handles are made of solid stainless steel and can be optionally complemented with slate or glass elements. Range 180 includes...
-
Activar Hiawatha 535/509/536/537 Solid 1 inch Diameter Pulls
• Plate & Pull Combinations • Standard Pulls • Push & Pull Bar Sets • Custom & Unique Pulls • Full Height Pulls • Door Protection Plates & Edges • Auto...
-
19 Inch Low Height
transfer surface....
-
Activar Hiawatha HG111 & HG112 Straight Tubular Pulls and HG113 & HG114 Push Bars
• Plate & Pull Combinations • Standard Pulls • Push & Pull Bar Sets • Custom & Unique Pulls • Full Height Pulls • Door Protection Plates & Edges • Auto...
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
Sargent AL 80 Alarmed Exit Panic Door Hardware
SARGENT’s AL-80 Series Exit Devices are designed for areas requiring a stand-alone alarm on outward swinging doors....
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
4.6.5 PASSENGER LOADING ZONES
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 in all directions....
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
4.6.6 Passenger Loading Zones
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....
-
SDC Bollard Post with Push Plate or Touch Panel
Practical solution for surface mount or in-ground installation....
-
Table 2: Summary of Department of Transportation Survey
±1/8" (±3 mm) riser, ±1/4" (±6 mm) tread 13 Placement of detectable warning surfaces 0 2 in. 0.78 in....
-
Adaptive Surfing Makes the Ocean Accessible for People Who Use Wheelchairs - Rolling On, Episode 5
See how Arianny Ramirez rides Rockaway Beach’s waves on a surfboard—even though she needs a wheelchair to get around on land. Go to g.co/LGa11y and find out how Local Guides can make...
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer surfaces....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
Wheelchair Accessible Gates
Web sites with designs that allow wheelchair access while restricting access by ATVs and motorcycles are listed near the end of this tech tip. The best Web site was that of Scottish...
-
4.1.6(3)(d)(i)
(i) Where it is technically infeasible to comply with clear opening width requirements of 4.13.5, a projection of 5/8 in maximum will be permitted for the latch side stop.
-
6.14.2 Gate Hardware
Gate hardware shall comply with operable controls requirements in ABAAS section 309.4 and 404.2.7.
-
General Elements
Most scoping provisions apply to both interior and exterior elements where provided throughout facilities and sites (and are not limited to those in corridors as shown here).
-
CRL Jackson 1200 Series Push Pad Door Exit Devices
08 7100 CRL Jackson 20 Series Push Pad Door Exit Devices For 1-3/4" Narrow, Medium, and Wide Stile Aluminum, Wood or Hollow Metal Doors "Soft-Touch" Smooth Action Push-Pad Field...
