11B-703.3 and 11B-703.5 shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
Search Results "Adjustable Height Exam Table"
-
11B-504.8 Floor identification
-
907.2.4 Group F
A manual fire alarm system shall be installed in Group F occupancies that are two or more stories in height and have an occupant load of 500 or more above or below the lowest level of exit...
-
1008.1.9.7, Item 5
THIS DOOR WILL OPEN IN 15 [30] SECONDS ALARM WILL SOUND” Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm)....
-
Triax 2000
A large tripod that can be raised to a fall height above the highest play surface on a playground. ...
-
§ 37.3 Alteration
rehabilitation, reconstruction, historic restoration, changes or rearrangement in structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
4.3 Reach Ranges
4.3 Reach Ranges Figures 14-15 and Table 4 show the standards from the four countries related to reach from a wheeled mobility device....
-
Selling Beauty: Marketing High-End Art and Design Books
Most books are sold on their words; art and coffee table books are sold on their physical presence. These are books as furniture, as status symbols, and as aesthetic objects....
-
Re: Service Counters
The entire depth of the lowered counter at 34" max height must be provided to allow for this unimpeded interaction instead of the higher employee counter condition which prevents equal access...
-
Turning Radius
Table 19 of this report shows the friction factors based on 85th percentile speeds. Additionally, the friction factors suggested by AASHTO are provided for comparison....
- Pilot Rock LDW-36/18 Campfire Ring
- Johnny G KRANKcycle® Cross Trainer by Matrix
- Spectrum Aquatics Summit 500BP Therapy Pool Lift (Battery Powered)
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
Dressing, Fitting, or Locker Rooms
Operating mechanisms provided on accessible lockers must also meet ADAAG provisions for their operation and height....
-
I. Introduction
The purpose of this Minority Report is to make a formal recommendation for a minimum transfer surface low height of 19 inches for diagnostic imaging medical equipment....
-
R308.1.2.1 Platform and Vehicle Floor Coordination
The Department of Transportation regulations (49 CFR parts 37 and 38) require the height of the vehicle floor and the station platform to be coordinated so as to minimize the vertical and...
-
T703.1 General
The symbol shall have a background field height of 4 inches (100 mm) minimum. The symbol and its background shall have a non-glare finish....
-
407.8.2 Side Reach
Where a side reach requires a reach over a portion of the ICT, the height of that portion of the ICT shall be 34 inches (865 mm) maximum....
-
Standard Units
Standard Units Units at conventional heights for use by standees are considered accessible to people who may bend or stoop with difficulty....
-
407.12.2 Side Reach
Where a side reach requires a reach over a portion of the ICT, the height of that portion of the ICT shall be 34 inches (865 mm) maximum....
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion of the automated teller machine or surround is not more than 10 in (255 mm), the maximum height...
-
A4.13.9 DOOR HARDWARE
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) form its bottom edge and be centered across the top....
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....