Section 611.4 covers the current ADA Standards for the height of the laundry compartment in top loading machines and front loading machines.
Search Results "Floor Designation"
-
Height: ADA Standard Section 611.4
-
11B-611.4 Height
Top loading machines shall have the door to the laundry compartment located 36 inches (914 mm) maximum above the finish floor....
-
11B-611.4 Height
Top loading machines shall have the door to the laundry compartment located 36 inches (914 mm) maximum above the finish floor....
-
Elevator requirement to new dining area on the mezzanine of an existing facility
The two keys to the answer are that no elevator would be required in the building in new construction because no floor in the building has more than 3000 square feet of floor area, but no...
-
Why Comprehensive "Bio-Hazard" Sanitization is Now a Standard for Emergency Services in Philadelphia
The floors are polished and free of the sticky residue that contaminated water leaves behind. The vents are clear, and the atmosphere feels light and healthy....
-
11B-407.4.8.2.1 Signal type
The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
-
11B-407.4.8.2.1 Signal type
The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
-
11B-604.8.1.4 Toe clearance
At least one side partition shall provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition...
-
11B-604.8.1.4 Toe clearance
At least one side partition shall provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition...
-
Entry Doors
Entry Doors Under the ADA Standards for Accessible Design, an accessible doorway must have a minimum clear opening width of 32 inches when the door is opened to 90 degrees....
-
11B-221.2.4 Temporary structures
Readily removable seats should be designed to facilitate easy, timely and frequent removal and installation. ...
-
11B-221.2.4 Temporary structures
Readily removable seats should be designed to facilitate easy, timely and frequent removal and installation....
-
Scope of Coverage
The Fair Housing Act defines "covered multifamily dwelling" to mean buildings consisting of four or more units if such buildings have one or more elevators; and ground floor units in other...
-
1009.2.1 Elevators required
In buildings where a required accessible floor is four or more stories above or below a level of exit discharge or where an accessible occupiable roof is above a story that is three or more...
-
11B-704.2.1.2 Forward approach
Where a forward approach is provided at a telephone within an enclosure, the counter may extend beyond the face of the telephone 20 inches (508 mm) into the required clear floor or ground...
-
11B-704.2.1.2 Forward approach
Where a forward approach is provided at a telephone within an enclosure, the counter may extend beyond the face of the telephone 20 inches (508 mm) into the required clear floor or ground...
-
M301.3.1 Transfer Supports
It will be located at the designated transfer location....
-
Bradley Advocate AV-Series Model AV30 Lavatory, Soap & Hand Dryer Informational Video
The all-in-one Advocate saves time, wet floors, and paper towel costs....
-
SHOPPING CENTER (OR SHOPPING MALL)
A shopping center may include a series of buildings on a common site, connected by a common pedestrian access route on, above or below the ground floor, that is either under common ownership...
-
Accessible Pathway & Corridor: Minimum Clear Floor Space Required for 360-degree Turn
This data depicts the amount of space required by users of wheeled mobility devices to perform a 360-degree turn. The bold dashed line in the table and figure indicates the...
-
Signal Type: ADA Standard Section 407.4.8.2.1
Section 407.4.8.2.1 covers the current ADA Standards for the signal type of audible elevator car indicators.
-
11B-809.10.6.4 Reinforcement for grab bars
grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor...
-
11B-809.10.6.4 Reinforcement for grab bars
grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor...
-
Beneficial Designs High Efficiency Trail Assessment Process (HETAP) Software 3.0 Wheeled Instrumentation Sensor Package for Data Collection
Key HETAP and UTAP Differences HETAP follows the same general principles as its predecessor, UTAP (the Universal Trail Assessment Process). Both collect objective trail...
