Transportation Institute at The Pennsylvania State University compared the slip-resistance needs of persons with mobility impairments and those without disabilities walking on level and ramped...
Search Results "Curb Ramp Width"
Filters
Commonly Searched Documents
-
Why are surface characteristics specified?
-
1002.4.3 Gaps
EXCEPTION: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
Some existing measurement protocols
system and waviness index, but these standards are not mandated for testing for accessibility, nor are there any standards for accessibility that can be tested other than overall slope of ramps...
-
11B-1002.4.3 Gaps
Exception: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
11B-1002.4.3 Gaps
Exception: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
Sec.36.304(c)(3)
These measures include, for example, removal of obstructing furniture or vending machines, widening of doors, installation of ramps, providing accessible signage, widening of toilet stalls...
-
§ 36.304(c)(3)
These measures include, for example, removal of obstructing furniture or vending machines, widening of doors, installation of ramps, providing accessible signage, widening of toilet stalls...
-
EZ Dock Transition Plate
Available in three widths: 3’, 4’, and 5’. Part# G200350, G200450 or G200550...
-
1005.3 Edge Protection
In such a design, curbs or barriers are not required....
-
1005.3 Edge Protection
In such a design, curbs or barriers are not required....
-
308.3.1 Unobstructed
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
1005.3 Edge Protection
In such a design, curbs or barriers are not required....
-
3.3.2 Experienced Clinicians
The Committee is considering two main options: minimum widths of 28” or 30”. “Tables” are equipment used by patients in supine, prone, or side-lying positions....
-
Trimco 1069 Series ADA Pocket Door Pull
Standard is for frame width up to 7" can be made for any frame width. Can be used on a 1-3/8" door, as well as a 1-3/4" door....
-
Handrails, Grab Bars, and Tub and Shower Seats [4.26]
Handrails, Grab Bars, and Tub and Shower Seats [4.26] ADAAG 4.26 provides technical requirements for: handrails at ramps [4.8] and stairs [4.9] grab bars at water closets...
-
Hoyer Heavy-Duty Power Lift with Optional Scale
Weight capacity - 700 lbs Product weight - 150 lbs Lifts patient from floor - Yes Max lifting range - 69" Minimum lifting range - 23.3" Base width...
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
Accessible Routes
Accessible route requirements in ADAAG address width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level, doors, egress, and areas...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The width of the patient scanning/imaging table (side to side) at the designated transfer location should be 28 inches minimum or the maximum extent technically feasible, but in all cases...
-
5.2.2 Transfer Surface Size Recommendations for M302
The transfer surface size has two components: width and depth. (See Figure 5.2.1.1) NPRM Proposed Provision: M302.2.2 Size....
-
D. Entering the Emergency Shelter
An accessible entrance must provide at least one accessible door with maneuvering space, accessible hardware, and enough clear width to allow people who use crutches, a cane, walker, scooter...
-
Character Proportion [4.30.2]
Consider uniform stroke widths which can make signs easier to read....
-
Doors and Gates in Series [§404.2.6]
Doors and Gates in Series [§404.2.6] At hinged or pivoted doors or gates in series, a separation is required that is at least 48” plus the width of doors or gates swinging into the space...
-
Doors and Gates Operated Only By Security Personnel [§404.1, Ex]
If automated, such doors or gates are required to comply only with provisions for clear width and thresholds, as well as applicable provisions of the referenced ANSI/BHMA Standards....
