[DSA-AC] The line where two surface planes with different slopes meet....
Search Results "Dining Surface"
-
GRADE BREAK
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
106.5.76 Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
Sold to the Highest Bidder: Building Better Auction Houses with Steel
While steel is a hard surface, the building structure allows for excellent acoustic tuning. We use perforated liner panels and spray-on acoustic insulation to dampen the reverb....
-
What Is the Future of SEO When AI Answers Replace Clicks?
Industry Reference Modern search platforms increasingly surface direct answers above traditional results, making authority, trust, and AI visibility more valuable than rankings alone....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Sec.36.403(c)(1)(ii)
(ii) Replacing an inaccessible floor surface in the customer service or employee work areas of a bank;...
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate FS 33538 of Federal Standard 595C....
-
§ 36.403(c)(1)(ii)
(ii) Replacing an inaccessible floor surface in the customer service or employee work areas of a bank;...
-
RAMP
A walking surface in an accessible space that has a running slope greater than 1:20....
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate 33538 of SAE AMS-STD-595A....
-
Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....