The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall. The side edge...
Search Results "Shower Drain"
-
11B-610.3.1 Rectangular seats
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall. The side edge...
-
Location of Controls
Comments indicated that this specification was not consistent with a corresponding figure showing the location on the side closest to the shower opening. Response....
-
11B-809.10.6.2 Slope
The slope of the shower floor shall be 1/2 inch (12.7 mm) per foot maximum in any direction and shall slope to a drain....
-
4. Shower Wand
Is there an adjustable height hand-held shower wand with at least a 60" long hose provided so persons who bathe from a seated position may wash and rinse with the directional spray?...
-
11B-608.2.1 Reserved
ETA Editor's Note The transfer type shower compartments prescribed by 2010 ADAS 608.2.1 are not recognized as an accessible shower in California....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-809.10.6.6 Controls
Controls and operating mechanisms shall comply with Section 11B-309.4.
-
11B-809.10.6.6 Controls
Controls and operating mechanisms shall comply with Section 11B-309.4.
-
1. Number of Roll-in Showers
If there are more than 50 guestrooms/suites in the facility, are the proper number of accessible rooms with roll-in showers provided per table 9.1.2 below....
-
Zurn Insulation Combination Kit: One Trap Protector, Two Stop Supply Protectors and One Offset Drain Protector
Z8946-3-NT Combination Kit: One Trap Protector, Two Stop Supply Protectors and One Offset Drain Protector FEATURES: Satin white PVC resin 3/8" Nominal wall with vandal resistant...
-
Curbs [4.21.7]
Curbs [4.21.7] Curbs are limited to ½ inch (measured from the room floor and the shower floor) so as not to interfere with entry to the shower....
-
11B-608.2.3 Alternate roll-in type shower compartments
11B-608.2.3 Alternate roll-in type shower compartments....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
Tile Redi Free® Barrier Free Base and Flash Installation Video
Redi Base shower pan installation...
-
4.21.7 Curbs
All of the designs reviewed were curbless, roll-in showers....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
608 Shower Compartments
[See subsections ...]
-
608 Shower Compartments
[See subsections ...]
-
ROLL-IN SHOWER STALLS
[See subsections ...]
-
4.21 Shower Stalls
[See subsections ...]
-
A4.21 Shower Stalls
[See subsections ...]
-
608 Shower Compartments
[See subsections ...]
-
A4.21 SHOWER STALLS
[See subsections ...]
