Additional language or an additional sign below the International Symbol of Accessibility shall state “Minimum Fine $250.”
Search Results "Electronic Signage"
Filters
Commonly Searched Documents
-
11B-502.6.2 Minimum fine
-
§ 1194.2(a)(2)
(2) When procuring a product, if an agency determines that compliance with any provision of this part imposes an undue burden, the documentation by the agency supporting the...
-
E.2. - Where an agency uses a best value "trade-off" source selection process, may it trade off applicable technical provisions of the Access Board’s standards where an offer provides strong technical merit, strong past performance, or a lower price?
The Access Board’s technical provisions are mandatory requirements that must be met (directly or through equivalent facilitation) unless (a) the product or service (if it is a...
-
11B-216.8.1 Geometric symbols
Geometric symbols complying with Section 11B-703.7.2.6 shall be provided at entrances to toilet and bathing rooms. Exceptions: Geometric symbols shall not be required at...
-
Directional Signs: ADA Standard Section 216.4.3
Section 216.4.3 covers scoping requirements in the current ADA Standards for directional signs.
-
A. Signs
A. If signs are provided for the following spaces, are the signs mounted on the wall (not the door) to the latch side of the door and centered 60" above the floor so that they can be...
-
11B-703.1.1.2 Inspection
Signs and identification devices shall be field inspected after installation and approved by the enforcing agency prior to the issuance of a final certificate of occupancy per...
-
11B-703.1.1.2 Inspection
11B-703.1.1.2 Inspection. Signs and identification devices shall be field inspected after installation and approved by the enforcing agency prior to the issuance of a final...
-
11B-703.1.1.2 Inspection
Signs and identification devices shall be field inspected after installation and approved by the enforcing agency prior to the issuance of a final certificate of occupancy per...
-
703.5.6 Height from Finish Floor or Ground
Visual characters shall be 40 inches (1015 mm) minimum above the finish floor or ground. EXCEPTION: Visual characters indicating elevator car controls shall not be required to...
-
703.5.6 Height From Finish Floor or Ground
Visual characters shall be 40 inches (1015 mm) minimum above the finish floor or ground. EXCEPTION: Visual characters indicating elevator car controls shall not be required to...
-
703.5.6 Height from Finish Floor or Ground
703.5.6 Height from Finish Floor or Ground. Visual characters shall be 40 inches (1015 mm) minimum above the finish floor or ground. EXCEPTION: Visual characters indicating...
-
1007.9 Signage
1007.9 Signage. Signage indicating special accessibility provisions shall be provided as shown: 1....
-
Van Accessible Signage
Comment. The proposed rule removed a requirement that the access designation for van parking include the term "van accessible" to clarify that both car and van drivers can use such...
-
Van Accessible Signage
Comment. The proposed rule removed a requirement that the access designation for van parking include the term "van accessible" to clarify that both car and van drivers can use such...
-
1009.9 Signage
Signage indicating special accessibility provisions shall be provided as shown: Each door providing access to an area of refuge from an adjacent floor area shall be identified by a...
-
11B-703.5.7 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 20 percent maximum of the height of the character. [2010 ADAS] 703.5.7 Stroke Thickness. Stroke...
-
703.4 Installation Height and Location
Signs with tactile characters shall comply with 703.4.
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character.
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character.
-
703.4 Installation Height and Location
Signs with tactile characters shall comply with 703.4.
-
703.5.7 Stroke Thickness
703.5.7 Stroke Thickness. Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character.
-
703.4 Installation Height and Location
703.4 Installation Height and Location. Signs with tactile characters shall comply with 703.4.
-
11B-703.4 Installation height and location
Signs with tactile characters shall comply with Section 11B-703.4.