The height of the lift seat shall be designed to allow a stop at 17 inches (432 mm) minimum to 19 inches (483 mm) maximum measured from the deck to the top of the seat surface when in the...
Search Results "Surface Discontinuities"
Filters
Commonly Searched Documents
-
11B-1009.2.4 Seat
-
Height of Tables or Counters [4.32.4]
Height of Tables or Counters [4.32.4] Counter and table surface heights (28 to 34 inches) should be specified in consideration of the intended use....
-
2.2.1 Demographic Information
., power chair, scooter), and within each type: make, model, age, armrests, footrests, drive wheels, controller, seat support surfaces and overall condition of the seating surface....
-
4.6.3* PARKING SPACES
Parking spaces and access aisles shall be level with surface slopes not exceeding 1:50 in all directions....
-
Is an accessible route required to rooftop levels?
., equipped with lighting, ventilation, and means of egress) that is “included between the upper surface of a floor and upper surface of the floor or roof next above” (§106.5)....
-
§ 38.95(c)(8) Handrails
grasp them from outside the car while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
§ 38.83(c)(8) Handrails
them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
§ 38.125(c)(8) Handrails
grasp them from outside the car while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
11B-1009.3.1 Sloped entries
Exception: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
R407.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 100 mm (4 in) diameter sphere, where any portion of the sphere is within 100 mm (4 in) of the finish surface....
-
T702.8 Contrast
Where provided, protective surfaces over signs shall have a non-glare finish....
-
1009.3.1 Sloped Entries
Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3 EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip...
-
M302.3.2 Armrests
Armrests on transfer sides are not permitted to obstruct access to the transfer surface. See M302.2.3 Exception....
-
11B-1009.3.1 Sloped entries
Exception: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
11B-1009.3.1 Sloped entries
Exception: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
Technical Requirements [1017]
The technical requirements for trails include specific provisions for the surface, clear tread width, passing spaces, tread obstacles, openings, running slope, cross slope, resting intervals...
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail vehicle resting on a flat surface...
-
TRANSIT BOARDING PLATFORM
[DSA-AC] A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
405.9.2 Curb or Barrier
curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface...
-
Rebuilding Together Of the Triangle - Raleigh, NC
wheelchair ramps Install railings and grab bars Widen doorways and modify bathrooms for accessibility Clear overgrown yards Paint interior and exterior surfaces...
-
1133A.2, Item 3
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
