Slide Locking Buttons including Emergency Release CL100 Mortise Lock Case IMPORTANT: Operable parts of hardware must be mounted 34 inches (865mm) minimum and 48 inches (1220 mm) maximum...
Search Results "Maximum Dimension"
Filters
Commonly Searched Documents
-
Cavity Sliders CL100 ADA LaviLock Hardware Set with 'Vacant / In Use' Indicator
-
Behavioral Safety Products #BF930 Suicide Resistant Attenda 3 Shelf Storage Unit
suicide resistant three shelf storage unit is composed of high impact polyethylene, abuse-resistant, heavy gauge material, and is formed from a one piece, rotationally molded design for maximum...
-
Brewer Access™ High-Low Exam Table 700
with Brewer's signature pass-through drawer system and it's backed by Brewer's standard 3-year warranty. 700 lb weight capacity Standard 3-year warranty Unique safety features Maximum...
-
AJW Architectural Products U815 Dual Toilet Tissue Dispenser w/ Mounted Shelf - Surface Mounted - Non-Controlled
Brackets: Fabricated of #18 gauge stainless steel formed for maximum strength. Toilet Tissue Dispenser: Fabricated of stainless steel with a #4 satin finish....
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Palmer Fixture BluStorm® Bolt High Speed Hand Dryer HD0923
outlets - high drying efficiency, quiet operation Thin profile, protrudes from the wall less than 4" Wide drying area with blue action light indicating sensor range and maximum...
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
8. Batteries
uses a ventilator, respirator, CPAP machine or FAA-approved POC to bring an adequate number of fully charged batteries onboard to operate the device for not less than 150% of the expected maximum...
-
1115B.4.1, Item 1
The centerline of the accessible water closet shall be 16 inches (405 mm) minimum and 18 inches (457 mm) maximum from the side wall or partition....
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The gripping surface of the transfer support should be located 1 ½ inches maximum measured horizontally from the adjacent edge of the transfer surface....
-
Alterations to Existing Facilities
Alterations to Existing Facilities The draft guidelines required alterations to existing facilities to comply with the requirements for new construction to the maximum extent feasible...
-
24. Educational setting
Section 104.34 prescribes standards for educating handicapped persons with nonhandicapped persons to the maximum extent appropriate to the needs of the handicapped person in question....
-
Element-by-Element Safe Harbor for Existing Facilities
For example: The 1991 Standards allowed light switches, thermostats, and other controls to be installed at a maximum height of 54 inches....
-
Trailhead Signs
minimum the following information: Trail name Length of the trail Type of surface on the trail Typical and minimum trail tread width Typical and maximum...
-
III-8.4000 Suit by the Attorney General
All violations found in the first suit against a covered entity are considered to be the first violation, so that the maximum penalty that may be assessed in that suit is $50,000....
-
Required Means of Egress [IBC §1007.1 (2003), §1003.2.13 (2000)]
For example, a business occupancy with no more than 30 occupants and a maximum exit access travel distance of 75 feet is permitted to have a single means of egress....
-
11B-1009.3.3 Handrails
The clear width between required handrails shall be 33 inches (838 mm) minimum and 38 inches (965 mm) maximum. Exceptions: 1. ...
-
Chapter 3: Building Blocks
Substantive revisions made in the final rule include: lowering the maximum height for side reaches from 54 to 48 inches (308.3.1) providing a limited exception from this...
-
610.3 Shower Compartment Seats
The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2....
-
F228 Depositories, Vending Machines, Change Machines, and Mail Boxes
These elements are subject to requirements for operable parts in section 309, which specify location within accessible reach ranges and maximum operating forces....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
