[2010 ADA Standards] 703.5.4 Character Proportions....
Search Results "ISO: International Organization for Standardization"
-
11B-703.5.4 Character proportions
-
11B-703.2.4 Character proportions
[2010 ADA Standards] 703.2.4 Character Proportions....
-
11B-703.2.5 Character height
[2010 ADA Standards] EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be ½ inch (13 mm)...
-
11B-809.4.1 Subsequent bathrooms
ETA Editor's Note The requirement for an accessible shower at subsequent bathrooms prescribed by CBC 11B-809.4.1 is not required by 2010 ADA Standards....
-
11B-1008.2.6 Ground surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....
-
11B-703.5.4 Character proportions
[2010 ADA Standards] 703.5.4 Character Proportions....
-
11B-703.2.4 Character proportions
[2010 ADA Standards] 703.2.4 Character Proportions....
-
11B-703.2.5 Character height
[2010 ADA Standards] EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be ½ inch (13 mm)...
-
11B-1008.2.6 Ground surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....
-
11B-809.4.1 Subsequent bathrooms
ETA Editor's Note The requirement for an accessible shower at subsequent bathrooms prescribed by CBC 11B-809.4.1 is not required by 2010 ADA Standards....
-
1.1.4 Appendices
code shall not apply unless specifically adopted by a state agency or adopted by a local enforcing agency in compliance with Health and Safety Code Section 18901 et. seq. for Building Standards...
-
The Division on Career Development and Transition (DCDT)
The mission of DCDT is to promote national and international efforts to improve the quality of and access to, career/vocational and transition services, increase the participation of education...
-
E202.7 Best Meets
Where ICT conforming to one or more requirements in the Revised 508 Standards is not commercially available, the agency shall procure the ICT that best meets the Revised 508 Standards consistent...
-
M101.1 Purpose
The proposed standards contain technical criteria for medical diagnostic equipment that is accessible to and usable by patients with disabilities....
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
5.2.2.1 Transfer Surface Width Recommendations for M302
recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position as described in its proposed standard...
-
B.3.iv - Who makes the determination that a product meets equivalent facilitation?
The vendor may assert that its product meets or exceeds the level of accessibility required by a particular standard through equivalent facilitation....
-
24.1 Q. What types of grab bars should the reinforcement be designed to accommodate and what types may be used if the builder elects to install grab bars in some units at the time of construction?
In determining what is an appropriate grab bar, builders are encouraged to look to the 1986 ANSI A117.1 standard, the standard cited in the Fair Housing Act....
-
§ 36.304(d)(2)(iii)
., elements for which there are neither technical nor scoping specifications in the 1991 Standards), and therefore those elements must be modified to the extent readily achievable to comply...
-
Alterations and Additions
This guide provides an introduction to the scoping requirements that form the basis for the Department of Justice’s 2010 ADA Standards and the Department of Transportation's ADA Standards...
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
INTRODUCTION
These changes include revised accessibility standards, called the 2010 Standards for Accessible Design (2010 Standards), which establish minimum criteria for accessibility in design and...
-
11B-201.1 Scope
[ADA Title III] §36.406(b) Standards for New Construction and Alterations; Scope of Coverage....
-
a. The employer's judgment
the quality or quantity of work that must be performed by a person holding a job, or be required to set lower standards for the job....
