This example of a retail facility shows how scoping requirements for certain elements and spaces (sales counters and fitting rooms) apply and indicates employee work areas....
Search Results "Non-Fixed Element"
Filters
Commonly Searched Documents
-
Example: Retail Facility
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
11B-707.4 Privacy
ETA Editor's Note The Department of Justice considers the communication-related elements of ATMs to be auxiliary aids and services, rather than structural elements, to which the Safe...
-
Section 4.1.6, Alterations (Preamble, Section-by-Section Analysis)
First, if any existing element or space is altered, the altered element or space must meet new construction requirements (section 4.1.6(1)(b))....
-
1. Accessible route(s)
Accessible element or space ANSI A117.1 section APPLICATION 1....
-
11B-707.4 Privacy
ETA Editor's Note The Department of Justice considers the communication-related elements of ATMs to be auxiliary aids and services, rather than structural elements, to which the Safe...
-
11B-707.4 Privacy
. ◼ ETA Editor's Note The Department of Justice considers the communication-related elements of ATMs to be auxiliary aids and services, rather than structural elements, to which the...
-
11B-101.1 General
This chapter contains scoping and technical requirements for accessibility to sites, facilities, buildings, and elements by individuals with disabilities....
-
11B-101.1 General
This chapter contains scoping and technical requirements for accessibility to sites, facilities, buildings, and elements by individuals with disabilities....
-
11B-101.1 General
This chapter contains scoping and technical requirements for accessibility to sites, facilities, buildings, and elements by individuals with disabilities....
-
4.3.4 Knee and Toe Clearances
The crease of the foot and lower leg in contact with the built element (Dorsal foot point as reference); 3....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
232.5.1 Cubicles and Counters
EXCEPTION: The inmate or detainee side of cubicles or counters at non-contact visiting areas not serving holding cells or housing cells required to comply with 232 shall not be required...
-
407.4.8.2.1 Signal Type
[ECTCR UFAS 4.10.13] EXCEPTION: For elevators other than destination-oriented elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with...
-
R302.7.4 Flangeway Gaps
Flangeway gaps at pedestrian at-grade rail crossings shall be 64 mm (2.5 in) maximum on non-freight rail track and 75 mm (3 in) maximum on freight rail track....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
407.4.8.2.1 Signal Type
EXCEPTION: For elevators other than destination-oriented elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz...
-
R103.3 Units of Measurement
Combining values from the two systems may result in non-compliance....
-
E202.6.1 Required Documentation
The Federal Acquisition Regulation (FAR) sets forth the documentation requirements for a determination of commercial non-availability by federal agencies subject to 508 requirements....
-
13.18 Quality Assurance Inspections
previously-identified standards issues) utilizing each Brand’s quality assurance checklists to verify appearance of items that can be checked in an average half-day review with a visible, non-intrusive...
-
11B-812.7.1 Location
Exception: Where four or fewer total EVCS are provided within a facility, the access aisle for non-angled van accessible spaces may be located on either the driver or passenger side of the...
-
Play Component
An element intended to generate specific opportunities for play, socialization, or learning....
-
Using the Tape Measure
A tape measure is used to measure the length, width, height, and depth of various elements including parking spaces and access aisles, routes, thresholds, doorways, and protruding objects...