[DSA-AC] “Approved” means meeting the approval of the enforcing agency, except as otherwise provided by law, when used in connection with any system, material, type of construction, fixture...
Search Results "Surface Material"
-
[A] APPROVED
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
Bradley 2 Station Verge Lavatory System LVRD2
Model LVRD2 Verge image gallery Available in Evero Natural Quartz Surface Evero Natural Quartz Materials are now GREENGUARD Certified as low-emitting materials...
-
11B-1009.2.4 Seat
The height of the lift seat shall be designed to allow a stop at 17 inches (432 mm) minimum to 19 inches (483 mm) maximum measured from the deck to the top of the seat surface when in the...
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided....
-
11B-1009.2.4 Seat
The height of the lift seat shall be designed to allow a stop at 17 inches (432 mm) minimum to 19 inches (483 mm) maximum measured from the deck to the top of the seat surface when in the...
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided....
-
11B-705.1.1.3.2
11B-705.1.1.3.2 Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
11B-705.1.1.3.2
Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
Transfer Height: ADA Standard Section 1002.5.2
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
§382.121(a)
priority storage areas or in overhead compartments or under seats, consistent with FAA, PHMSA, TSA, or applicable foreign government requirements concerning security, safety, and hazardous materials...
-
Cross Slope [1018.7.2]
When beach access routes are constructed of materials other than asphalt, concrete, or boards, cross slopes no steeper than 1:20 (5 percent) are allowed when necessary for drainage....
-
§8.54(c)
Methods for ensuring participation include, but are not limited to, qualified sign language and oral interpreters, readers, or the use of taped and Braille materials....
-
Sec.36.605(b)
(b) The Assistant Attorney General, after consultation with the Architectural and Transportation Barriers Compliance Board, and consideration of the materials and information submitted pursuant...
-
Accessible Presentation / Speaker’s Platform - Talk Show Style
Side tables should be provided (for water, notes, or other materials) for each guest. Individuals who use wheelchairs or scooters may need a higher side table than other guests....
-
§ 38.23(c)(1) Design load
support a load of 600 pounds, placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches, with a safety factor of at least 3 based on the ultimate strength of the material...
-
Baseline
on curb ramps All state transportation departments currently specify detectable warning surfaces on curb ramps in their standard drawings; most local transportation departments maintain...
-
R409.4 Height
Top of gripping surfaces of handrails shall be 865 mm (2.8 ft) minimum and 965 mm (3.2 ft) maximum vertically above walking surfaces, ramp surfaces, and stair nosings....
-
Guest Bathrooms
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds is applied at any point on the grab bar, fastener, mounting device, or supporting...
-
1010.1.5 Floor elevation
Variations in elevation due to differences in finish materials, but not more than ½ inch (12.7 mm). 5....
-
Transfer Supports
Materials in a variety of different shapes and sizes are used to manufacture transfer supports including metal, plastic, and rope....
-
Neo-Metro Urinal Divider Number 8949-N
Regularly Furnished: The 16 gage type 304 stainless steel divider includes a mounting channel with vandal resistant fasteners.The interior is sound deadened with fire-resistant material...
