As we look toward the continued development of disability policy, we must have a firm grasp on how we have reached this point....
Search Results "Firm Surface"
-
In Closing
-
Data Analyses
Data Analyses Net energy consumption – the additional energy utilized during walking in excess of resting levels – was calculated for each surface....
-
Interactive Illuminated Models
Interactive Illuminated Models Another promising new development expands on the concept of touch sensitive talking models by projecting light onto the model’s 3D surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
Transfer Devices for Use with Amusement Rides: ADA Standard Section 1002.6
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches 430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
ALIGNMENT OF 19-INCH RECOMMENDATION WITH ACCESS BOARD PROPOSED RULEMAKING
In its proposed rule, the Access Board proposed that the “height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured...
-
3.1.4. Digital vs. Analog Projection Systems
According to the data presented in Section 3.1.1, approximately 98 percent of all indoor auditoriums exhibit digital movies.16 Most of the large movie theaters are operated by the largest firms...
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
Boat Slips: ADA Standard Section 1003.2.1
Where handrail extensions are provided on gangways or transition plates, the handrail extensions shall not be required to be parallel with the ground or floor surface. 7....
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
9. What type of reasonable accommodations may employees with hearing disabilities need?
The IT specialist position requires frequent one-on-one meetings with the firm's president....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
Transfer supports should be provided for imaging equipment with transfer surfaces with depths of less than or equal to 24 inches....
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
Edge Protection
Edge Protection Where railings, guards, or handrails are provided, edge protection must be provided and extend a minimum of 2 inches above the ground or deck surface....
-
22. How can I get copies of the ASTM standards that apply to play areas?
American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428, www.astm.org: ASTM F 1292-99 Standard Specification for Impact Attenuation of Surface...
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
I. Public Toilet Rooms
In all public and common use toilet rooms throughout the Hotel and the Tower, Defendants will provide at least one lavatory with a counter-top that is 34 inches above the finish floor surface...
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...