This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location on trails, other than within facilities provided on...
Search Results "Dispenser Location"
-
F247.5 Outdoor Constructed Features
-
4.34.5.5(4) Controls
Faucets and other controls shall be located as shown in Fig. 37 and shall comply with 4.27.4....
-
4.34.5.4(3) Grab bars
Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 48....
-
F247.5 Outdoor Constructed Features
constructed features are provided on trails, other than within facilities specified in F247.4, at least 20 percent, but not less than one, of each type of outdoor constructed feature at each location...
-
Are redundant controls for an element required to comply?
If a redundant control is located in a different space, however, it must comply. All light switches are required to comply....
-
§ 37.135(b) Initial submission
provided in §37.141 of this part, each entity shall submit its initial plan for compliance with the complementary paratransit service provision by January 26, 1992, to the appropriate location...
-
604.8.1.5 Grab Bars
A side-wall grab bar complying with 604.5.1 shall be provided and shall be located on the wall closest to the water closet....
-
106.5.6 Amusement Attraction
Any facility, or portion of a facility, located within an amusement park or theme park which provides amusement without the use of an amusement device....
-
11B-101.2 Reserved.
lavatory pipes under sinks to prevent burns; 15) Installing a raised toilet seat; 16) Installing a full-length bathroom mirror; 17) Repositioning the paper towel dispenser...
-
11B-101.2 Reserved.
lavatory pipes under sinks to prevent burns; 15) Installing a raised toilet seat; 16) Installing a full-length bathroom mirror; 17) Repositioning the paper towel dispenser...
-
SDC Bollard Post with Push Plate or Touch Panel
use with Push Plates, Touch Panel Columns & Exit Switches 6” square with 1/8” walls Black HDPE mortised removable cap with secure transmitter mount Standard single gang prep located...
-
HEWI Hinged Support Rail Duo
Instead of two hinged support rails, one L-shaped support rail can be used if the toilet is located in a corner....
-
Neo-Metro Urban Stainless Steel Toilet 8950-3-ADA-PFS
Floor Mounted Against Wall Flushing: Cistern (supplied) Toilet Bowl Shape: Elongated Environmental/Health: Contains Recycled Material , Recyclable Waste Location...
-
Sargent HP Bored Lock with Push/Pull Trim
The paddle shape and location create a comfortable target for door activation without using hands....
-
ELKAY Filtered EZH2O® Mechanical Surface Mount with Battery-powered visual monitor LMASMB
Non-Electric Surface mount design - ideal for installations where electrical wiring is not easily accessible or locations looking to reduce electrical usage Push-button activation delivers...
-
Feature 3 - Building Entrance
An accessible meeting location must have at least one accessible entrance that is connected to an accessible route....
-
Forward Approach
Corresponding changes have been made to the specifications for spout location (602.5)....
-
Accessible Check-out Aisle Signage
The proposed rule required that this identification be placed in the same location as the identifying number or type of check-out aisle....
-
General Scoping for TTYs
of public accommodation and commercial facilities) where four or more pay phones are provided at a bank, within a floor, building, or on an exterior site, a TTY is required at each such location...
-
Specifications for Alternate Roll-in Shower Controls
In the final rule, the Board has clarified these specifications and provided more detail on their location depending on whether the shower is equipped with a seat....
-
809.4 Toilet Facilities and Bathing Facilities
Toilet and bathing fixtures required to comply with 603 through 610 shall be located in the same toilet and bathing area, such that travel between fixtures does not require travel between...
-
R309.4 Curb Ramps or Blended Transitions
Curb ramps shall not be located within the access aisle. Advisory R309.4 Curb Ramps or Blended Transitions....
-
Parallel Parking Spaces (R309.2) (Section-by-Section Analysis)
In alterations where the street or sidewalk adjacent to the parking spaces is not altered, an access aisle is not required provided the parking spaces are located at the end of the block...
-
R302.7.2 Vertical Surface Discontinuities
The allowance for vertical surface discontinuities is for occasional expansion joints and objects such as utility covers, vault frames, and gratings that cannot be located in another portion...
