(2) If a public entity has responsibility or authority over streets, roads, or walkways, its transition plan shall include a schedule for providing curb ramps or other sloped areas where...
Search Results "Dining Area"
Filters
Commonly Searched Documents
-
§ 35.150(d)(2)
-
11B-505.3 Continuity
Exception: In assembly areas, ramp handrails adjacent to seating or within the aisle width shall not be required to be continuous in aisles serving seating....
-
§ 37.163(e)
the transportation service the entity is able to provide, the public entity may keep the vehicle in service with an inoperable lift for no more than five days (if the entity serves an area...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
Appendix D: Photometric Measurements
Where: L1 is the luminance of the lighter area and L2 is the luminance of the darker area....
-
Toilet and Bathing Facilities: ADA Standard Section 806.2.4
Toilet and bathing fixtures required to comply with 603 through 610 shall be permitted to be located in more than one toilet or bathing area, provided that travel between fixtures does not...
-
11B-602.9 Pedestrian protection
The protected area within which a drinking fountain is located shall be 32 inches (813 mm) wide minimum and 18 inches (457 mm) deep minimum, and shall comply with Section 11B-305.7....
-
Signs
Section 216.10 of the 2010 Standards requires each covered assembly area to provide signs at each auditorium to inform patrons that assistive listening systems are available....
-
G. Chapter 6: Wheelchair Spaces and Securement Systems
With the exception of two areas, this chapter has been neither significantly reorganized nor substantively revised from the proposed rule....
-
4.33.3* Placement of Wheelchair Locations
Wheelchair areas shall be an integral part of any fixed seating plan and shall be provided so as to provide people with physical disabilities a choice of admission prices and lines of sight...
-
Visual Alarms [4.28.3]
Visual alarms are required in hallways, lobbies, restrooms, and any other general usage and common use areas, such as meeting and conference rooms, classrooms, cafeterias, employee break...
-
3.4 Staff-Related Barriers and Solutions
Simple/Low cost Involved / High cost Staff is hard to find when you need help Work out a signal with one or two staff members who will be in the area...
-
III-4.2200 Specialties
It is not considered discriminatory for a public accommodation with a specialty in a particular area to refer an individual with a disability to a different public accommodation if --...
-
§ 38.159(d)(2) Location and size
The securement system shall be placed as near to the accessible entrance as practicable and shall have a clear floor area of 30 inches (760 mm) by 48 inches (1220 mm)....
-
11B-219.3 Receivers
Receivers complying with 706.2 shall be provided for assistive listening systems in each assembly area in accordance with Table 219.3....
-
Exception 8
to provide, priority should be given to those elements that will provide the greatest access in the following order: An accessible entrance; An accessible route to the altered area...
-
11B-219.3 Receivers
Receivers complying with 706.2 shall be provided for assistive listening systems in each assembly area in accordance with Table 219.3....
-
11B-219.3 Receivers
Receivers complying with 706.2 shall be provided for assistive listening systems in each assembly area in accordance with Table 219.3....
-
General: ADA Standard Section 234.1
Section 234.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for amusement rides.
-
11B-201.1 Scope
All areas of newly designed and newly constructed buildings and facilities and altered portions of existing buildings and facilities shall comply with these requirements....
-
11B-234.3 Minimum number
These rides are not exempt from the other provisions in Section 11B-234 requiring an accessible route to the load and unload areas and to the ride....
-
Wikk Industries Inc. Bollard With Push Plate Part #BPR8 SM AINS32D (630)
Flat Recessed area for ADA switch and Card Reader. Welded angle top to the back. Shown on the bollard- 6x6-3 US32D (630), Switch is sold separately....
-
Sec.36.403(c)(1)(iii)
(iii) Redesigning the assembly line area of a factory; or...
-
Sec.36.403(c)
(c) Alterations to an area containing a primary function....
