(b) Clearance between counters and all opposing base cabinets, countertops, appliances or walls is at least 40 inches.
Search Results "Extended Floor Surface"
Filters
Commonly Searched Documents
-
7(1)(b)
-
7(2)(b)(ii)
(ii) Where the door swings out, a clear space is provided within the bathroom for a person using a wheelchair or other mobility aid to position the wheelchair such that the person is...
-
ADA & Level Boarding Guidance - Platform Height
49 CFR §§37.41-43; 37.9(a), (d); 49 CFR Part 37, App. A (810.5.3) DECEMBER 14, 2011
-
2. a. iv. Path-of-Travel (wheelchair) space allowances
2. a. iv. Path-of-Travel (wheelchair) space allowances.xii In general, a 36” wide accessible route is needed with a slightly larger space provided at corners. If a 180° turn is...
-
4.34.5.2 WATER CLOSETS
[See subsections ...]
-
AJW Architectural Products U648 Series C-fold/Multifold Towel Dispenser & Waste Receptacle Combination w/ Extended Waste - Recessed
Product Features Fabricated of #22 gauge stainless steel with a #4 satin finish Holds 600 c-fold or 800 multifold towels Waste receptacle has a 6 gallon capacity Unit features an extended...
-
703.4.1 Height above Finish Floor or Ground
703.4.1 Height above Finish Floor or Ground....
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
-
Public Buildings: ADA Standard Section 217.4.2.1
Section 217.4.2.1 covers scoping requirements in the current ADA Standards for TTYs on the floor of a public building.
-
Floor Designations
The proposed rule specified that tactile floor designations at the hoistway be 60 inches above the floor, measured from the baseline of the characters (407.2.4)....
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer gripping surface should be located within the minimum and maximum heights....
-
Willoughby Industries ASETWS-1490-FM-HC Ligature-Resistant Floor Mounted Siphon Jet Water Closet
ASETWS-1490-FM-HC Ligature resistant floor mounted siphon jet series water closet Fixture shall be fabricated from 14 gauge, type 304 stainless steel....
-
11B-902.4.1 Clear floor or ground space
A clear floor space complying with Section 11B-305 positioned for forward approach shall be provided....
-
1010.1.5 Floor elevation
There shall be a floor or landing on each side of a door. Such floor or landing shall be at the same elevation on each side of the door....
-
11B-703.8.9 Height above floor
Low resolution VMS characters shall be 40 inches (1016 mm) minimum above the floor of the viewing position, measured to the baseline of the character....
-
Common Use Areas in Residential Facilities—Section 203.8 of the 2010 Standards
The only exception would be common use areas provided on upper stories of a non-elevator building provided the same common use areas are provided on the ground floor....
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
Transfer supports should be required on both sides of the transfer surface and be movable or removable so they can be out of the way during transfer....
-
A Wheelchair Rider's Guide to the California Coast
Explore, enjoy, protect. Rolling across the sand in a beach wheelchair Fishing from an accessible pier Hiking an accessible trail or...
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer support should be a minimum length of 15 inches positioned so that the transfer support overlaps the minimum depth of the transfer surface by 80%....
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
