Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
Stairway Handrails Requirements in the ADA Standards (§504)
-
11B-407.2.3.2 Reserved
ETA Editor's Note Imposing additional requirements regarding characters and colors, the preceding 2013 CBC requirements pertaining to elevator hoistway signs are more...
-
21. Q: Is there a limit to the amount of money my agency must spend to alter an existing police facility?
A: Yes. It is the same legal standard of "undue burden" discussed earlier with regard to the provision of communication aids. Your agency is not required to undertake alterations...
-
T404 Level Boarding and Alighting
[See subsections ...]
-
7(2)(b)(iii)
(iii) When both tub and shower fixtures are provided in the bathroom, at least one is made accessible. When two or more lavatories in a bathroom are provided, at least one is made...
-
11.2 Q. Under the individual building test, at what point of the planned entrance is the measurement taken?
A. On a horizontal plane, the center of each individual doorway should be the point of measurement when measuring to an arrival point, whether the doorway is an entrance door to the...
-
7(2)(b)(i)
(i) Where the door swings into the bathroom, there is a clear space (approximately, 2' 6" by 4'0") within the room to position a wheelchair or other mobility aid clear of the path of...
-
11B-407.2.3.2 Reserved
ETA Editor's Note Imposing additional requirements regarding characters and colors, the preceding CBC requirements pertaining to elevator hoistway signs are more stringent...
-
11B-407.2.3.2 Reserved
ETA Editor's Note Imposing additional requirements regarding characters and colors, the preceding CBC requirements pertaining to elevator hoistway signs are more stringent...
-
Portable Floor Lifts
Portable Floor Lifts The most common types of lifts in medical settings are portable with a U-shaped base that moves along the floor on wheels....
-
224 Transient Lodging Guest Rooms
(1) Kitchens within housing units containing accessible sleeping rooms with mobility features (including suites and clustered sleeping rooms) or on floors containing accessible sleeping...
-
Why are surface characteristics specified?
Why are surface characteristics specified? Over twenty-seven million Americans report some difficulty in walking....
-
11B-233.3.1.2.6 Public housing facility site impracticality
The remaining ground floor residential dwelling units shall comply with the following requirements: 1. Grab bar reinforcement complying with Section 11B-609. 2. ...
-
Landscape Forms Inc. Sort Recycling Units
This flexible system of collection bins and organizing basket for interior and exterior use was designed specifically for recycling. Created with sustainability in mind, it offers a...
-
Magnuson Group SMOKE Waste & Ash Receptacle
Designed by Mattiussi Ecologia Spa, SMOKE is a clean and compact ash and trash combination unit that fits perfectly into any exterior or interior space. Made of steel plate with a...
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and maximum...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
M305.2.3 Height (Section-by-Section Analysis)
Board sought input from the public in question 20 of the MDE NPRM preamble, on whether a transfer support height requirement of 6 inches minimum and 19 inches maximum above the transfer surface...
