Timing (Section-by-Section Analysis) Pedestrian signal phase timing must comply with referenced MUTCD standards and use a pedestrian clearance time that is calculated based on pedestrian walking...
Search Results "Walking Surface"
-
Pedestrian Signal Phase Timing (Section-by-Section Analysis)
-
§ 36.403(e)(2)
(2) An accessible path of travel may consist of walks and sidewalks, curb ramps and other interior or exterior pedestrian ramps; clear floor paths through lobbies, corridors, rooms, and...
-
Sec.36.403(e)(2)
(2) An accessible path of travel may consist of walks and sidewalks, curb ramps and other interior or exterior pedestrian ramps; clear floor paths through lobbies, corridors, rooms, and...
-
Introduction
For the effective communication required by the Americans with Disabilities Act (ADA) of 1990, the WALK/DON’T WALK indications of visual pedestrian signal heads should be conveyed to pedestrians...
-
Standards
when Considering Footwear Traction ASTM F 1637 - 02 Standard Practice for Safe Walking Surfaces ASTM F 1951 - 99 Wheelchair Work Measurement Method ASTM PS 83 -...
-
Detectable Warnings: ADA Standard Section 705
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
General: ADA Standard Section 705.1
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
Current Accessibility Guidelines That Apply to the Forest Service
Fishing piers and platforms New or reconstructed: Picnic areas Fire rings Picnic tables Grills Woodstoves Benches Cooking surfaces...
-
Height Above Finish Floor or Ground: ADA Standard Section 703.4.1
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
11B-405.9.2 Curb or barrier
or barrier shall be provided that prevents the passage of a 4-inch (102 mm) diameter sphere, where any portion of the sphere is within 4 inches (102 mm) of the finish floor or ground surface...
-
11B-405.9.2 Curb or barrier
or barrier shall be provided that prevents the passage of a 4-inch (102 mm) diameter sphere, where any portion of the sphere is within 4 inches (102 mm) of the finish floor or ground surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
802.4.2 Identification
Seats with folding or retractable armrests are intended for use by individuals who have difficulty walking....
-
802.4.2 Identification
Seats with folding or retractable armrests are intended for use by individuals who have difficulty walking....
-
Accessible Route
required to comply with 4.9, it is recommended that routes to them meet the requirements for accessible routes since certain specifications, such as clear width, can benefit people with walking...
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate 33538 of SAE AMS-STD-595A....
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate 33538 of SAE AMS-STD-595A....
-
Entrance
An entrance includes the approach walk, the vertical access leading to the entrance platform, the entrance platform itself, vestibules if provided, the entry door(s) or gate(s), and the...
-
Wet Locations: ADA Standard Section 903.7
Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water....
-
CURB CUT
[DSA-AC] An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
11B-705.1.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with Section 11B-705....