Lavatories without base cabinets shall be installed with the centerline 18 inches (457 mm) minimum from an adjoining wall or fixture to allow for forward approach. Lavatories with...
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
11B-809.10.8.1 Location
-
11B-703.5.6 Height from finish floor or ground
Visual characters shall be 40 inches (1016 mm) minimum above the finish floor or ground. Exceptions: 1. Visual characters indicating elevator car controls shall not be...
-
11B-703.5.6 Height from finish floor or ground
Visual characters shall be 40 inches (1016 mm) minimum above the finish floor or ground. Exceptions: Visual characters indicating elevator car controls shall not be required...
-
1133A.4.1, Item 2
Base cabinets directly under sinks and work surfaces shall be removable as required in Section 1133A.3....
-
Ticketing (Assembly areas, not parking.)
The regulations also address the following: group sales, hold and release of accessible seating tickets, ticket transfer and secondary market ticketing....
-
Healthcraft Invisia ADA Serenaseat™ Folding Shower Seat
Product Specification The shower seat shall have a Brazilian Walnut back rest and seating surface. The seating surface shall be 32"/81cm in width....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
1133A.4.1, Item 2
Base cabinets directly under the kitchen sink counter area and work surface shall be removable as required in Section 1133A.3....
-
608.4 Seats
A folding or non-folding seat shall be provided in transfer type shower compartments....
-
California Department of Managed Health Care - Physical Access to Health Care Fact Sheet
If You Use a Wheelchair or Have a Hard Time Walking
-
Pilot Rock N-20 Series Charcoal Grill
N Series grill cooking grates are fabricated using 5/8" dia. steel bars for support handles, and 1/2" dia. steel bars for the cooking surface. ...
-
11B-502.6 Identification
Signs shall be 60 inches (1524 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. [2010 ADAS] 502.6 Identification. ...
-
11B-502.6 Identification
Signs shall be 60 inches (1524 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. [2010 ADAS] 502.6 Identification. ...
-
11B-502.6 Identification
Signs shall be 60 inches (1524 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. [2010 ADA Standards] 502.6 Identification....
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply with M305.3.1.2...
-
Balco FMS-A and FMS-V Roll-Up Floor Mat
Dirt and moisture collect underneath the grate surface to keep floors clean and reduce maintenance. Rails can be replaced without dismantling the entire grid system....
-
Spectrum Industries Inc. Instructor Media Console and Workstation
Even special ergonomic conditions – sit or stand – are addressed with two standard worksurface heights. Choose from standard and optional laminates to achieve the look you want....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
-
1012.5 Slope
This section requires the slope of the surface of parking spaces and pull-up spaces to not be steeper than 1:48 in any direction....
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
R304.5.3 Cross Slope
R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
-
1133A.4.1, Item 3
3. The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent...
