Technically infeasible means: “… something that has little likelihood of being accomplished because existing structural conditions would require removing or altering a load-bearing member...
Search Results "Load and Unload Area"
Filters
Commonly Searched Documents
-
Alterations
-
F206.2.3 Multi-Story Buildings and Facilities
Where a two story public building or facility has one story with an occupant load of five or fewer persons that does not contain public use space, that story shall not be required to be...
-
11B-502.4 Floor or ground surfaces
Where two parking stalls share the same access aisle, a full depth aisle is required; in diagonal parking, the geometric layout will require additional access aisle depth to satisfy the loading...
-
11B-502.4 Floor or ground surfaces
Where two parking stalls share the same access aisle, a full depth aisle is required; in diagonal parking, the geometric layout will require additional access aisle depth to satisfy the loading...
-
11B-502.4 Floor or ground surfaces
Where two parking stalls share the same access aisle, a full depth aisle is required; in diagonal parking, the geometric layout will require additional access aisle depth to satisfy the loading...
-
1009.2.4 Seat Height
of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the raised (load...
-
Are accessible parking spaces required on a site where valet service is provided but vehicles are parked off site, such as in a public parking garage or on public streets?
Parking facilities with valet parking must provide accessible parking spaces to allow self-parking by people with disabilities (and must also provide an accessible passenger loading zone...
-
1132A.8.1 Lever-type hardware
or locks shall be curved with a return to within ½ inch (12.7 mm) of the door to prevent catching on the clothing of persons during egress in Group R and U Occupancies with an occupant load...
-
1132A.8.1 Lever-type hardware
or locks shall be curved with a return to within ½ inch (12.7 mm) of the door to prevent catching on the clothing of persons during egress in Group R and U Occupancies with an occupant load...
-
4.26.3(4)
Tensile force induced in a fastener by a direct tension force of 250 lbf (1112N) plus the maximum moment from the application of 250 lbf (1112N) shall be less than the allowable withdrawal load...
-
1009.2.6 Footrests and Armrests
If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
-
1009.2.6 Footrests and Armrests
If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
-
Do accessible routes that cross vehicular ways need to be marked as a crossing?
The Standards only require access aisles at accessible parking spaces and accessible passenger loading zones to be marked....
-
Willoughby Industries ETW-1445-BS-HC Toilet for 45-degree Chase Wall
Fixture shall withstand loadings up to 2,000 lbs. with no measurable deflection and loadings up to 5,000 lbs. with no permanent damage....
-
§ 38.113(d)(4) Exception
vehicles shall be coordinated with the platform in existing stations such that the horizontal gap shall be no greater than 4 inches and the height of the vehicle floor, under 50% passenger load...
-
Can curbs be used to indicate areas with less than 80” of vertical clearance?
The standards specify a maximum height (27”) for the leading edge of barriers so they are within cane sweep, but a minimum height is not specified. Curbs may be mistaken for a step...
-
Populas Vox Perfect Corner Workstation
The Vox Perfect Corner boasts a surface area of 6ft x 6ft, provides extra-low and extra-high range of adjustment, sleek design and amazing durability....
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
When the transfer supports latch into a locked position, the transfer supports must meet the required load conditions without movement....
-
1133B.2.4.2
Regardless of the occupant load, there shall be a floor or landing on each side of a door. 1133B.2.4.2 Maneuvering clearances at doors. ...
-
New Construction
Passenger Loading Zones -- Sections 209 and 503. Assembly Areas -- Sections 221 and 802. Sales and Service -- Sections 227 and 904....
-
§ 38.73(d)(3) Exception
vehicles shall be coordinated with the platform in new and key stations such that the horizontal gap shall be no greater than 4 inches and the height of the vehicle floor, under 50% passenger load...
-
§ 38.53(d)(3) Exception
vehicles shall be coordinated with the platform in new and key stations such that the horizontal gap shall be no greater than 4 inches and the height of the vehicle floor, under 50% passenger load...
-
§ 38.93(d)(4) Exception
vehicles shall be coordinated with the platform in new and key stations such that the horizontal gap shall be no greater than 4 inches and the height of the vehicle floor, under 50% passenger load...
-
1009.2.6 Footrests and Armrests
If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
