Cross Slope The cross slopes of gangways, transition plates and floating piers that are part of an accessible route must be designed and constructed not to exceed a maximum of 2...
Search Results "Side Transfer Surface"
-
Cross Slope
-
4.3.7 Slope
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
4.3.7 SLOPE
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
Electronic instruments
Electronic instruments have been developed to measure floor flatness. Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance
-
Side guard protocol
Side guard protocol: From initial setup, two side guards adjusted 6” (15.2 cm) higher than the subject’s WMD seat were attached, and subjects were asked to perform a level height transfer...
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Exterior lighting shall be provided to illuminate walking surfaces of boarding and alighting areas when the doors of non-rail vehicles are open....
-
Ronick Matting Systems BaseMat 300 Entrance Floor Mat
At 3/8" depth this aluminum entrance floor mat is suited for a wide range of applications ranging from surface mounted to recessed installations....
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M301.1 General
Where diagnostic equipment is used by patients in a supine, prone, or side-lying position, it shall comply with M301....
-
A4.22.3 Clear Floor Space
It is important to keep in mind that the placement of the lavatory to the immediate side of the water closet will preclude the side approach transfer illustrated in Figure A6(b)....
-
A4.27.3 Height
Fig. A8 further illustrates mandatory and advisory control mounting height provisions for typical equipment. Electrical receptacles installed to serve individual...
-
3.5.3 Signs in General
If materials need to be obtained from or manipulated on a sign or kiosk, the sign or kiosk shall be designed to meet the reach ranges in section 308 of the ABAAS.
-
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces For imaging equipment with transfer surfaces, the Committee recommends a positioning support...
-
§ 38.115(a)
The diameter or width of the gripping surface of interior handrails and stanchions shall be 11/4 inches to 11/2 inches or shall provide an equivalent gripping surface....
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Q1: Pavement Treatment Considered an Alteration and Curb Ramp Compliance
Q1: When a pavement treatment is considered an alteration under the ADA and there is a curb ramp at the juncture of the altered road and an existing sidewalk (or other prepared surface for...
-
Basic Components for Accessible and Usable Public and Common Use Areas or Facilities
[See subsections ...]
-
11B-203.9 Employee workstations
-206.2.8 _|Accessible Routes; Employee Work Areas|_, 11B-207.1 _|Accessible Means of Egress; General|_, 11B-215.3 _|Fire Alarm Systems; Employee Work Areas|_, 11B-302 _|Floor or Ground Surfaces...
-
Just Manufacturing 42" Stainless Steel Grab Bar
Type-304, 18 Gauge Stainless Steel 42" Length x 1-1/2" Diameter with concealed screws Brushed stainless finish Grab bar to wall distance...
-
Bobrick 42" Straight Grab Bar Peened B-6806.99 x 42
42" (1065mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 42" Straight Grab Bar Peened B-5806.99 x 42
42" (1065mm) long, 1-1/4" (32mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 42" Straight Grab Bar B-6806 x 42
42" (1065mm) long, 1-1/2" (38mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
