With good coordination and the use of their hips and legs, kids can pump the Flexus to new heights....
Search Results "Sink Height"
Filters
Commonly Searched Documents
-
Kompan, Inc. Flexus GXY919
-
Attachment B – Code References
rehabilitation, reconstruction, historic restoration, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
Sizewise SW Low Boy
The SW Low Boy® is changing the way hospitals and long term care facilities address fall prevention by offering the industry’s first bariatric low bed with a low resting height of 7” and...
-
GameTime ADA Wide Ramp Attachment 3D
Specifications Model Number - 91044 Fall Height - Deck Height Age Groups - 2 to 5 or 5 to 12 years...
-
CRL Jackson 900 Series Floor Mounted Door Closers
Capacity, 42" Doors The Perfect Door Closer to Support CRL's Patch Hardware Narrow 3-1/16" (78 mm) Width Interchangeable Spindle Heights 5 Year Limited Warranty...
-
SafePath BigHorn™ Ramps
surface in threshold design, much safer than aluminum Peel-and-stick tape for immediate installation Perfect for wheelchairs, scooters and electric chairs Can be vertically cut for height...
-
Atlantis Railing
SPECIFICATIONS: Ramp Sections: The SunRailTM AccessEasy System is offered in a standard height of 42" with a handrail height of 36"....
-
GPK UPPERTONE Unassisted Muscle Strengthening System for Quadriplegics
This allows quads to make all necessary adjustments, such as station height, station width, and resistance, unassisted....
-
BTX Intelligent Fashion Motorized Drapery Systems
BTX prides itself on being able to offer the height of design, better heating and air conditioning energy conservation, and the convenient control that patrons have come to know and expect...
-
1. Width and Depth of Wheelchair Spaces
Because the final rule also requires raised platforms over 1½ inches in height to provide edge protection that is a minimum of 2 inches high from the surface of the platform (See M303.2.6...
-
II. Rulemaking History
The committee members reached a consensus on all of their recommendations, except for the recommended lowest or minimum height for adjustable-height transfer surfaces....
-
Meeting ANSI Standard S12.60 Requirements
For classrooms where there is no fixed lecture position for the teacher, such as those for lower grades, and where ceiling heights are less than ten feet, the best option is to place most...
-
1.3.1 Overview of NPRM
Equipment to Which Technical Criteria Applies Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301) Transfer surface, including height...
-
Road Roughness Measurements
(Figure 8) An inertial profiler uses an accelerometer and a non-contacting sensor, such as a laser transducer, to measure height....
-
M303.2.4 Equipment Clearances (Section-by-Section Analysis)
Due to the reorganization of the equipment clearances provision in the final rule, the knee and toe clearance requirements for the other equipment section have been renamed depth and height...
-
H. Your Obligation to Provide Services and Equipment
[Sec. 382.21(a)(4)] On-board wheelchairs must be equipped with footrests, armrests which are movable or removable, adequate occupant restraint systems, a backrest height that permits assistance...
-
III 3.11000 Insurance
ILLUSTRATION: An amusement park requires individuals to meet a minimum height requirement that excludes some individuals with disabilities for certain rides because of a limitation in its...
-
1023.9 Stairway identification signs
comply with Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
Standards that measure needed physical or mental ability to perform a job
Possible accommodations might include lowering the shelf-height, providing a step stool or other assistive device....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
F226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
404.2.10 Door and Gate Surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height...
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
A positioning support (for transfer surfaces >24” deep) is to extend horizontally along the side of the patient scanning/imaging bed/table with a length of 12 to 16 inches and a height...
