The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area.16 As...
Search Results "PLZ: Passenger Loading Zone"
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
-
Section 37.9 Standards for Transportation Facilities
One further clarification concerning the implication of this provision deals with a bus loading island at which buses pull up on both sides of the island....
-
I. Ensuring Compliance Now and In the Future
But public entities can use their authority under zoning and land use laws, as well as plan review processes, to ensure that private developers comply with the accessibility requirements...
-
Compliance date
According to these commenters, large projects take several years from design to occupancy, and can be subject to delays from obtaining zoning, site approval, third-party design approval...
-
Compliance date. (Section-by-Section Analysis)
According to these commenters, large projects take several years from design to occupancy, and can be subject to delays from obtaining zoning, site approval, third-party design approval...
-
Construction and Maintenance Practices
The key to accessible parking is the striped zone next to it that ensures adequate space next to the vehicle to allow people to get into and out of their vehicle even if they use a wheelchair...
-
Engineered Wood Fiber
emerging playground surfacing trends is to install a unitary surface, such as PIP or TIL, as the primary accessible route to accessible equipment and fill the remainder of the equipment use zones...
-
I. Introduction to the Study
Ground surfaces that are part of the accessible use and also located in the use zones must meet ASTM F1292‒99/04 Standard Specification for Impact Attenuation of Surface Systems Under and...
-
Section 37.73 Purchase or Lease of Used Non-Rail Vehicles by Public Entities Operating a Fixed Route System
., Passenger Transport, or contacting the transit trade association, American Public Transit Association (APTA), to determine whether accessible used vehicles are available....
-
Section 36.311 Mobility Devices (Section-by-Section Analysis)
In developing the policy, the public accommodation has considered the dimensions of the EPAMD, including its height, in relation to the common areas of the ship and the safety of other passengers...
-
Mohawk Group Matuto Carpet Tiles
.: 304.8mm・}0.39mm; Length: 609.6mm・}0.8mm Static Load Limit ASTM F970 - Passes, modified - 1500 psi Residual Indentation ASTM F1914 - Passes - Average less than 8% Slip Resistance...
-
LaCantina Aluminum Thermally Controlled Slider System
0.3 CFM/FT2 Water Infiltration Result ASTM-E 547 6.0 PSF DP 40 No Leakage No Leakage Uniform Load...
-
LaCantina Multi-slide Thermally Controlled Aluminum Sliding Door System
0.3 CFM/FT2 Water Infiltration Result ASTM-E 547 6.0 PSF DP 40 No Leakage No Leakage Uniform Load...
-
LaCantina Contemporary Aluminum Thermally Controlled Door System
Water Infiltration ASTM-E 547 5.25 psf No Leakage No Leakage Uniform Load Deflection ASTM-E 330...
-
M305.2.2 Length (Section-by-Section Analysis)
This commenter (a manufacturer) stated that a transfer support that is a minimum of 15 inches in length would make it even more difficult to comply with load bearing requirements and recommended...
-
Accessibility
Firmness is a direct measure of the depression of a surface when a controlled load is placed on it....
-
Excel Dryer, Inc. LEXAN® Series Hand Dryers
Motor for 50 Hz Units shall be a universal 1/10 HP. 4200 R.P.M. at rated load with sealed lubricated ball bearings. It shall be insulated by a resilient mounting....
-
Americans with Disabilities Act
Subpart B, Part II applies to public transportation provided by the National Railroad Passenger Corporation and commuter authorities by intercity and commuter rail....
-
B. Regulatory Flexibility Act
Small firms operate OTRBs for a variety of purposes, but predominant uses include: provision of fixed route passenger service within or among cities, passenger charter services, airport...
-
§35.150 Existing Facilities
should be noted that ‘‘structural changes’’ include all physical changes to a facility; the term does not refer only to changes to structural features, such as removal of or alteration to a load-bearing...
-
II. Cost-disproportionality Is Only a Factor Under Certain Circumstances
feasible” would not require entities “to make building alterations that have little likelihood of being accomplished without removing or altering a loadbearing structural member unless the load-bearing...
-
How is slip resistance measured?
There are three critical stages in an individual's gait: 1) touchdown, 2) full load, and 3) push-off....
-
Location of accessible routes to stages. (Section-by-Section Analysis)
They noted that premium seats may have to be removed and that load-bearing walls may have to be relocated....
-
Section 504
(3) This section does not require recipients to make building alterations that have little likelihood of being accomplished without removing or altering a load-bearing structural member...
