In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
Search Results "Curb Ramp Surface"
Filters
Commonly Searched Documents
-
240.1 General
-
240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
seca 664 - electronic wheelchair scale_without comments - seca1840
Easy access is assured by its extremely low platform and the self-lowering ramps. The secure side rails give additional safety....
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
M301.2.1, M302.2.1 Transfer Height
measured from the floor to the top of the transfer surface...
-
Tread Obstacles on Outdoor Recreation Access Routes
A tread obstacle is anything that interrupts the evenness of the tread surface....
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
1009.8 Two-way communication
Two-way communication systems are not required on floors provided with ramps conforming to the provisions of Section 1012....
-
Technical Memorandum TM 2013-14 Dining Surfaces
dining surfaces based on TAS 201.1....
-
Triax 2000
A large tripod that can be raised to a fall height above the highest play surface on a playground. ...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
11B-240.1 General
In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the...
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
-
1009.8 Two-way communication
Two-way communication systems are not required on floors provided with ramps conforming to the provisions of Section 1012....
-
Stairways [§504]
Stairways [§504] Requirements for stairways address treads and risers, surfaces, nosings, and handrails....
-
11B-250 Circulation paths
[See subsections ...]
-
4.6.5 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment. Supports (transfer or positioning) should be located 1 ½ inches maximum from the transfer surface....
-
Elevator Car Requirements [§407.4.2 – §407.4.5]
Elevator Car Requirements [§407.4.2 – §407.4.5] Other requirements for elevator cars include: compliant floor surfaces a maximum 1¼” horizontal clearance between car...
-
M303.3.3.1 Running Slope
Ramp runs shall have a running slope not steeper than 1:12....
-
Smith System Husky Rectangle Activity Table 24″ Deep
Available in two height ranges, 15-24″ and 21-30″. 24″ deep models work surface available in size 24″x60″....
-
1008.4 Play Components
Ground level play components on accessible routes and elevated play components connected by ramps shall comply with 1008.4....
-
1008.4 Play Components
Ground level play components on accessible routes and elevated play components connected by ramps shall comply with 1008.4....
