Search Results "Compartment Door"
Filters
Commonly Searched Documents
-
Figure 404.2.4.1(f) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(h) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(j) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(d) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Pull Side – Drawing from the U.S. Access Board
-
SDC Sure Exit® PSB560 REX Pressure Sense Exit Bar
Stable and Reliable Pressure Sense Technology Building codes essentially state that egress through access controlled doors must not require prior knowledge of operational requirements...
-
Sargent 8500 Narrow Design Rim Exit Device
Features Designed for narrow stile applications such as aluminum frame full glass doors Single and double doors with mullion Single point rim latching device...
-
Sargent 8888 Reversible Rim Exit Device
The 8888 is designed for standard width stile applications on wood and metal doors and has 7 functions determined by the trim function....
-
HEWI Panic Bar EN 1125
Special solutions for exit doors must enable fast escape in an emergency....
-
L-Shaped Seats: ADA Standard Section 610.3.2
Section 610.3.2 covers the current ADA Standards for L-shaped shower compartment seats.
-
7(2)(a)
(a) Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Cabinets under lavatories are acceptable provided the...
-
§100.205(c)
(c) All covered multifamily dwellings for first occupancy after March 13, 1991 with a building entrance on an accessible route shall be designed and constructed in such a manner that—
-
Figure 404.2.4.1(i) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side with Closer – Drawing from the U.S. Access Board
-
608.3.1 Transfer Type Shower Compartments
In transfer type compartments, grab bars shall be provided across the control wall and back wall to a point 18 inches (455 mm) from the control wall....
-
TownSteel TRXL Grade 1 Cylindrical Lock with Ligature Resistant Trim
It fits standard 161 door prep....
-
608.3.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
Corbin Russwin Inc. ED5000 Series Exit Device
Aesthetics Over the past 100 years, Corbin Russwin has been well-known for weaving pleasing aesthetics and inventive designs into architectural door hardware, and today’s wide stile exit...
-
Stanley QED 100 Series Grade 1 Extra Heavy Duty Exit Devices
Certifications ANSI/BHMA A156.3 Series Grade 1 UL/cUL listed (3-hours) for "A" label single door applications (4' x 8') UL10C/UBC 7-2 (1997) Positive Pressure Rated UL10B Pressure...
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
The escutcheon plate is sloped at a low profile, from the door to the lever handle itself, to eliminate any further ligature points, and maintains extremely tight tolerances. ...
-
Allegion Falcon 1990 Series Cross Bar Exit Devices
: Hex dogging standard Cylinder: Rim, key entry (NL) or hold back (HB) available (field selectable) Sizes: Field adjustable width, 41" crossbar standard fits 3' 8" x 7' door...
-
DORMA 8000 Series Exit Device
For paired doors where a full-width opening is only occasionally required, removable mullions are used. Doors are fitted with rim exit devices and normally function as single doors....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Figure 404.2.4.1(g) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side with Closer and Latch – Drawing from the U.S. Access Board
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
