cross-manufacturer, non-proprietary consensus standards depending on the nature of the system with which it is exchanging information—namely, a traditional telephone network or Internet-based...
Search Results "Clearance Around Base"
-
410.6.3 Interoperability (Section-by-Section Analysis)
-
7.4.5.1 Size
A space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or The intersection of two trails providing a T-shaped space complying with ABAAS section 304.3.2 where the base...
-
§1630.16(c)(1) General policy
part does not encourage, prohibit, or authorize a covered entity to conduct drug tests of job applicants or employees to determine the illegal use of drugs or to make employment decisions based...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
1002.4.4.2 Side Entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
Doorways
In the final rule, clarification has been added that the 32 inch minimum clearance applies to those doors "providing user passage" into and within guest rooms not required to be accessible...
-
11B-1002.4.4.2 Side entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
Q3.) What are the types of “manufacturing processes” that were anticipated where the advisory says “tolerances recognized by this provision include… “those that may be a necessary consequence of a particular manufacturing process”?
Therefore, the manufacturing tolerances and the construction tolerances must both be considered when measuring the clearances between a grab bar and a tile wall....
-
Handrails
Handrails must comply with the following: Clearance between handrail gripping surfaces and adjacent surfaces shall be 1 1/2 inches (38 mm) minimum. ...
-
1002.4.4.2 Side Entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
2.5.2.2 International Organization for Standardization (ISO) Standards
Risk management plays a critical and central role in the design of medical devices, and it also ties into IEC 60601-1 and FDA’s expectations for quality systems and premarket clearance or...
-
H29
Accessible Shower Stall Minimum Size and Clearances Accessible Shower Stall Grab Bars and Seat, Shower, and Control Area...
-
1002.4.4.2 Side Entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
Question 16
What is the optimal clearance needed under a bed to accommodate a mechanical lift?...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Forward Approach Power Chair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Forward Approach Manual Wheelchair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Error/Omission: When a transfer shower is used, it is often larger than the required 36" x 36" size.
Requirement: 4.21.2 Size and Clearances. Except as specified in 9.1.2, shower stall size and clear floor space shall comply with Fig. 35(a) or (b)....
-
11B-1002.4.4.2 Side entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
11B-1002.4.4.2 Side entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to...
-
Oval Window Audio Microloop III - Small Area Hearing Loop Systems
One wireless microphone transmitter (choice of UHF wireless hand held “pass around” or lavaliere transmitter microphone w/user selectable frequencies)....
-
I. Introduction to the Study
accessible route (1:16 or 6.25%), maximum cross slope (1:48 or 2.08%), minimum clear width (60 inches), limit on a change of level along the route (no more than .50 inch), and vertical clearance...
