For example, if the vertical distance between where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level is 10 feet, the gangway would...
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
Gangway Slope and Rise Exceptions
-
206.2.8 Employee Work Areas
However, passenger elevators used for vertical transportation between stories are not considered "work area equipment" as defined in Section 106.5....
-
1. Typical Issues for Individuals Who Use Wheelchairs, Scooters, or Other Mobility Devices
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
206.2.8 Employee Work Areas
However, passenger elevators used for vertical transportation between stories are not considered "work area equipment" as defined in 106.5....
-
Part 1. Typical Issues for Voters Who Use Wheelchairs, Scooters, or Other Mobility Devices
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
Slope and Rise [4.8.2]
Slope represents the proportion of vertical rise to horizontal length and can be represented as a ratio (as in ADAAG), percentage, pitch or in degrees....
-
Phase II – Textures
color patterns was divided further into different variations of each pattern (Spots - large bold spots, small random spots, and small evenly spaced spots; Stripes - horizontal stripes, vertical...
-
Toilet Compartment Access
So it is still a latch side approach with exactly the same dimensions, including minimum clearances. I'm assuming that we are looking at compliance with the 2010 ADA Standards. ...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
Obstructions shall not be vertically less than 1 inch nor be horizontally more than 3 inches from the edge of the patient support surface to provide unobstructed access to the transfer surface...
-
1134A.6 Showers
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
11B-226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
R302.3.2 Shared Use Paths
See AASHTO Guide, 5.2.1 Width and Clearance....
-
Viewing Scopes [1011.2, 1011.3, and 1011.8]
Knee and toe clearance that complies with section 306 of the ABA Standards must be provided under the viewing scope (figure 25)....
-
Exterior Features
Sidewalks not exceeding a 5% slope (with a 2% side slope) Passenger loading zone with zero clearance exterior route for people using mobility devices....
-
11B-226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
11B-226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances. ◼...
-
Scope: ADA Standard Section 201.1
Section 201 discusses the scope of the ADA Standards.
-
Pilot Rock AT Series Traditional A-Frame Picnic Table With Steel Braces - Using Recycled Plastic
The design meets or exceeds current ADA guidelines for wheelchair accessibility and provides for wheelchair access at both ends (30" wide, 27" under table top and 19" knee plus 5" toe clearances...
-
Hoyer Heavy-Duty Power Lift with Optional Scale
Description: Hoyer's Heavy-Duty Power Lift features a power operated base with a clearance of 4.5"....
-
PEMKO 5" Heavy Duty Threshold No. 1715
For 1715 thresholds, allow a 5/8 inch door clearance....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2009-PK
About Latching Panic Saddle Thresholds Latching Panic thresholds are designed to work in conjunction with surface applied vertical rod exit devices....
-
Waterless Co. No-Flush Urinal Anza 2005
Trap insert to be of a vertical flow type with 360 degree perimeter openings and installed by press fit. Trap must be replaceable and refillable....
-
Salsbury Industries See Through Metal Locker Single Tier 3 Wide
Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping hoods, end bases and front bases Corner, top and vertical...
