Where a forward reach is unobstructed, the high forward reach shall be 48 inches (1220 mm) maximum and the low forward reach shall be 15 inches (380 mm) minimum above the finish floor or...
Search Results "Expected Maximum Flight Duration"
-
308.2.1 Unobstructed
-
803.5 Coat Hooks and Shelves
Shelves shall be 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
Williams Sound PPA 457 NET PRO PERSONAL PA® PRO FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
Activar Hiawatha 535/509/536/537 Solid 1 inch Diameter Pulls
Since 1954, Hiawatha has been providing consistent customer service with the high-quality materials and finishes that you have come to expect. ...
-
Currently, the DCFC time limit is 30 minutes maximum. New larger battery capacity will take longer to get 80% charge – i.e. Chevy Bolt EV, Tesla Model 3, 2018 Nissan LEAF, etc. Can we reconsider the time limit?
RESPONSE: The 30 minute time limit applies to drive-up EVCS of any type. This design option allows brief charging and queuing for charging service, and does not consider that...
-
11B-1003.3.1 Boat slip clearance
Each 10 feet (3048 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1524 mm) wide minimum. Exceptions: 1. ...
-
11B-1003.3.2 Boarding pier clearances
Every 10 feet (3048 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1524 mm) wide minimum. Exceptions: 1....
-
1003.3.2 Boarding Pier Clearances
Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum. EXCEPTIONS: 1....
-
1003.3.1 Boat Slip Clearance
Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum. EXCEPTIONS: 1....
-
11B-404.2.9 Door and gate opening force
Interior hinged doors and gates: 5 pounds (22.2 N) maximum. 2. Sliding or folding doors: 5 pounds (22.2 N) maximum. 3. ...
-
Standing Supports (M304.3 and M305.3)
The bottom of the support would be required to be 34 inches minimum and 37 inches maximum above the standing surface....
-
11B-404.2.9 Door and gate opening force
Interior hinged doors and gates: 5 pounds (22.2 N) maximum. 2. Sliding or folding doors: 5 pounds (22.2 N) maximum. 3....
-
11B-404.2.9 Door and gate opening force
The force for pushing or pulling open a door or gate other than fire doors shall be as follows: Interior hinged doors and gates: 5 pounds (22.2 N) maximum....
-
Midmark 641 Barrier-Free® Power Procedures Chair
Narrow patient support surface, slim back section and tuck away side rails provide maximum patient accessibility and supports proper posture Powered seat, back, foot and tilt offer multi-positioning...
-
Hadrian Inc. Gladiator Athletic Lockers
Maximum Ventilation Fully ventilated doors and sides with 0.5” x 1” (13 mm x 25 mm) oval perforations allow for maximum air circulation as well as visual access....
-
AquaTrek2 ADA Wading Pool Ramp
The Wading Pool Ramp will have a slope ratio that is technically feasible, readily achievable, and is based on the ADA maximum extent feasibility requirements for any wading pool. ...
-
11B-1009.5.6 Size
Each transfer step shall have a tread clear depth of 14 inches (356 mm) minimum and 17 inches (432 mm) maximum and shall have a tread clear width of 24 inches (610 mm) minimum....
-
604.8.3 Coat Hooks and Shelves
Shelves shall be located 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor. [ECTCR UFAS 4.25.3, Fig. 38, 4.23.9, 4.34.5.3(3)]...
-
1009.4.3 Wall Depth and Length
The depth of the transfer wall shall be 12 inches (305 mm) minimum and 16 inches (405 mm) maximum....
-
803.5 Coat Hooks and Shelves
Shelves shall be 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground. [ECTCR UFAS 4.25.3, Fig. 38]...
-
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment
Supports (transfer or positioning) should be located 1 ½ inches maximum from the transfer surface....
-
C1-d
[ADA Standards § 4.3.8] Yes No Note: Level changes between 1/4 inch and 1/2 inch should be beveled (sloped) at 1:2 maximum....
-
Sec.36.405(a)
.), or are designated as historic under State or local law, shall comply to the maximum extent feasible with section 4.1.7 of appendix A to this part....
-
R406.2 Unobstructed Forward Reach
Where a forward reach is unobstructed, the high forward reach shall be 1220 mm (4.0 ft) maximum and the low forward reach shall be 380 mm (1.25 ft) minimum above the finish surface....
