Specifications in 4.34.2 and 4.34.3 were modified in June 1993 to allow either a forward or side approach and to provide further guidance on side reach heights....
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
Scoping [4.1.3(20)]
-
5.3.4 Grab Bars
In such cases, the riser shall have vertical or nearly vertical sides and a flat area on each side of the seat that is about 3 inches (75 millimeters) wide. ...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
-
Hager Companies Round Offset Door Pull 23Q
Round Offset Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special orders....
-
Hager Companies Round Wrought Door Pull 5D
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special orders....
-
Doors in a Series
The required separation between doors and gates in series and specifications for maneuvering clearances at doors will ensure sufficient space regardless of the door swing....
-
Nystrom Building Products MatDesign Roll-Up Mats
MatDesign™ Roll-Up Mats Aluminum rail mats with ball and socket aluminum hinges with drain holes to allow debris and moisture to flow through the mat Hinges maintain their integrity...
-
A4.2.4 CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS
The space requirements in this standard are based upon maneuvering clearances that will accommodate most larger wheelchairs. Fig....
-
Front grab bar protocol
Two conditions in random order were tested: 1) front grab bar and no side guard and 2) both front grab bar and side guard present in the setup. ...
-
1009.5.2 Transfer Space
by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered along a 24 inch (610 mm) minimum side...
-
Edge Protection [§405.9]
Edge protection is not required at: ramps no higher than 6” that have side flares ramp landings serving an adjoining run or stairway sides of ramp landings with...
-
Clear Floor or Ground Space: ADA Standard Section 1008.4.2
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-403.5.1 Clear width
The clear width for aisles shall be 36 inches (914 mm) minimum if serving elements on only one side, and 44 inches (1118 mm) minimum if serving elements on both sides....
-
Paperwork Reduction Act
This rule does not contain any paperwork or recordkeeping requirements and does not require clearance under the PRA....
-
Components: ADA Standard Section 402.2
Section 402.2 covers the current ADA Standards for components of an accessible routes.
-
11B-810.6.3 Station names
Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle....
-
11B-802.1.2 Width
It should be noted that although side access to the wheelchair space is allowed, companion seating in compliance with Section 11B-802.3 must also be provided adjacent to each wheelchair...
-
Accessible Route Into and Through the Business
Customers with disabilities will not be able to shop in a store if the route through an entry plaza is too narrow because of a display of snow blowers, if the maneuvering clearance alongside...
-
Table Surface Height
Some commenters also recommended a higher minimum height of 29 inches instead of 28 inches to allow a more comfortable knee clearance. Response....
-
407.12 Reach Height (Section-by-Section Analysis)
Specifically, this section would establish requirements for position (i.e., vertical reference plane), forward reach, and side reach....
-
11B-1009.5.2 Transfer space
by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered along a 24 inch (610 mm) minimum side...
