If the side reach is over an obstruction, the reach and clearances shall be as shown in Figure 11B-5D(c)....
Search Results "Handrail Clearance"
-
1118B.6
-
Automatic Doors and Power Assisted Doors [4.13.12]
Some power-assists are activated by opening the door manually (and must meet ADAAG requirements for maneuvering clearance in 4.13.6 and opening force in 4.13.11) while others may be activated...
-
Designed Use
For example, pack and saddle stock require higher and wider clearances than do hikers, so a trail managed for both foot travel and horse use would have a designed use of "Pack and Saddle...
-
Kitchen Counters, Walls, and Floors
Staggered stud construction to prevent noise transmission to other rooms Zero clearance kitchen entries with less than 1/4” change of elevation throughout the accessible route. ...
-
3.3.10 90-Degree Turn
While all of the standards compared in this report have requirements for “wheelchair turning spaces”, only the U.S. and Canada have requirements specifically for 90-degree or L-Turn clearances...
-
Clear Floor Space: Minimum Clear Floor Space Required - Manual, Power & Scooter
The clear floor area width dimension also informs the minimum clearance width for successful passage through corridors, doorways, and wheelchair ramps....
-
Federal Elevator Serenus LULA Elevator
Stainless Steel Handrail Automatic control UL/CSA listed 14″ pit depth minimum Arrival gongs in cab Direction indicators in cab ADA Phone...
-
902 Dining Surfaces and Work Surfaces
Some commenters also recommended a higher minimum height of 29 inches instead of 28 inches to allow a more comfortable knee clearance. Response....
-
TABLE OF CONTENTS
Positions CHAPTER 3: BUILDING BLOCKS 301 General 302 Floor or Ground Surfaces 303 Changes in Level 304 Turning Space 305 Clear Floor or Ground Space 306 Knee and Toe Clearance...
-
Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Recycled Plastic
8 ft. long table is wheelchair accessible at both ends which meet or exceed current ADA guidelines for wheelchair accessibility (30" wide, 27" under table top and 19" knee plus 5" toe clearances...
-
Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Lumber
8 ft. long table is wheelchair accessible at both ends which meet or exceed current ADA guidelines for wheelchair accessibility (30" wide, 27" under table top and 19" knee plus 5" toe clearances...
-
Kohler® Mazz Single-Handle Pull-Down Sprayer Kitchen Faucet in Vibrant Stainless
Single lever handle is simple to use and makes adjusting water temperature easy High-arc gooseneck spout and 360-degree spout rotation offer superior clearance for filling pots and cleaning...
-
TABLE OF CONTENTS
4.19 Lavatories and Mirrors 4.20 Bathtubs 4.21 Shower Stalls 4.22 Toilet Rooms 4.23 Bathrooms, Bathing Facilities, and Shower Rooms 4.24 Sinks 4.25 Storage 4.26 Handrails...
-
Fur out the wall
Just need to make sure all other clearances, (42" from center line to adjacent wall/fixture is clear, etc.) ...
-
Feature 4 - Routes to the Meeting Space
Therefore, objects that do not provide sufficient head clearance or that are mounted too high and protrude into a route can become hazards because they cannot be detected by people who use...
-
226 and 902 Dining Surfaces and Work Surfaces
Section 902.2 requires the provision of accessible knee and toe clearance....
-
PART 3: ACCESSIBLE EXAMINATION ROOMS
The features that make this possible are: an accessible route to and through the room; an entry door with adequate clear width, maneuvering clearance, and accessible hardware;...
-
Notes
The committee recognizes that future visionaries may be able to “re-vision” new devices to provide greater clearances and smaller base supports....
-
226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
Temporary Solutions for Election Day - Hallways and Corridors - Voters Who are Blind or Who Have Low Vision
Problem Two: Ceiling or wall-mounted television monitor has less than 80 inches of clearance between the floor and the bottom of the unit....
-
R404 Clear Spaces (Section-by-Section Analysis)
Clear spaces are permitted to include knee and toe clearance and to be positioned for either forward or parallel approach to an element, unless another requirement specifies otherwise....
-
Mounting Height
It is also consistent with the minimum headroom clearance required for protruding objects....
-
Door and Gate Hardware [§404.2.7]
Recommendations: Specify hardware that is usable with a closed fist of loose grip Bars, pulls, and similar hardware should provide sufficient knuckle clearance (1½” minimum...
