Thresholds with a change in height between ¼ inch (6.35 mm) and ¾ inch (19.05 mm) shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
Search Results "Vertical Platform Lift"
-
1132A.4.1, Item 2
-
R210.3 Shared Use Paths
The AASHTO Guide recommends 10 feet vertical clearance along shared use paths, and 8 feet minimum vertical clearance in constrained areas....
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Where doorways have ramps, bridgeplates or lifts, the illumination shall be 1 foot-candle (11 lux) minimum for a distance of 3 feet (915 mm) measured beyond the edge of the ramp, bridgeplate...
-
§ 36.406(f)(3)
(3) Wheelchair spaces and companion seats are not located on (or obstructed by) temporary platforms or other movable structures, except that when an entire seating section is placed on temporary...
-
§382.101(e)
., unusually severe weather; unexpected mechanical problems) prevent the use of a lift....
-
BRW1000 Bariatric Wheelchair Scale Demo
The digital BRW1000 scale features a low-profile platform with two-way integral ramps for efficient bariatric wheelchair loading....
-
4.4.3 Implications of Mammography Equipment Components
In order to get an image with sufficient detail, a woman’s breast must rest on top of the breast platform and her chest wall needs to be flush with the front edge of the breast platform....
-
Clear space
The angle the WMD was positioned with respect to the transfer station was measured from the front edge of the platform as shown in Figure 2....
-
Website Accessibility Evaluation
The evaluation shall: (a) identify any ways that www.edx.org, the mobile applications, or the Platform are out of conformance with WCAG 2.0 AA; and (b) make recommendations to improve the...
-
B. Accessible Route
Is there a route to these 5% accessible fixed tables that allows at least 36" clear width and has no abrupt vertical level changes greater than 1/4"?...
-
e-ii
[ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for 12 inches of horizontal distance....
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
610.4 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
903.6 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
Location: ADA Standard Section 502.3.4
Section 502.3.4 covers the current ADA Standards for the required location of access aisles.
-
Salsbury Industries Designer Wood Locker Six Tier Box Style 1 Wide
units 1 wide units come fully assembled while 3 wide units require minor assembly All locker doors are 12" wide x 3/4" deep All locker doors include heavy duty concealed hinges and a lift...
-
Salsbury Industries Designer Wood Locker Six Tier Box Style 3 Wide
units 1 wide units come fully assembled while 3 wide units require minor assembly All locker doors are 12" wide x 3/4" deep All locker doors include heavy duty concealed hinges and a lift...
-
11B-106.5 Defined terms
OCCUPIABLE SPACE OPEN RISER OPERABLE PART PASSENGER ELEVATOR PATH OF TRAVEL PEDESTRIAN PEDESTRIAN WAY PERMANENT PERMIT PICTOGRAM PLACE OF PUBLIC ACCOMMODATION PLATFORM...
-
§382.101(c)
(c) You are using an aircraft subject to an exception from the lift boarding and deplaning assistance requirements under §382.97(a)-(c) of this subpart;...
-
T302.1 General
EXCEPTION: Walking surfaces on lifts shall not be required to comply with T302....
-
I. Parking Garage
Does the parking garage serving the lodging facility allow at least 98" of vertical clearance for vehicles with raised roofs to approach, use and exit the accessible parking spaces?...
-
1132A.4.1, Item 2
Thresholds with a change in height between ¼ inch (6.35 mm) and 3/4 inch (19.05 mm) shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)...
-
MEANS OF EGRESS
A continuous and unobstructed path of vertical and horizontal egress travel from any occupied portion of a building or structure to a public way....
-
11B-610.4 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
