Closers with regular or hold-ope arm mount hinge side or top jamb....
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
Allegion LCN 1000 Surface Mounted Door Control
-
604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
Angled (Front-In) Parking
ADAAG's requirement for an access aisle on either side of a space (they can be shared by two spaces) is based on the assumption that drivers can head in or back in as needed....
-
11B-604.9.1 Location
The water closet shall be located with a wall or partition to the rear and to one side....
-
H5
If there is a raised threshold, is it no higher than 3/4 inch at the door and beveled on both sides?...
-
D5. Raised Threshold
If there is a raised threshold, is it no higher than 3/4 inch at the door and beveled on both sides?...
-
11B-812.7.1 Location
Access aisles at vehicle spaces shall not overlap the vehicular way and may be placed on either side of the vehicle space they serve except for van accessible spaces which shall have access...
-
Allegion Falcon SC60 Series Surface Mounted Door Closer
Specifications Meets ANSI A117.1 ANSI/BHMA A156.4, Grade 1 UL Listed 1 3/8" diameter piston Closer mounts hinge side, top jamb or parallel arm...
-
Lateral grab bar use
The lateral grab bar was used least by subjects for the Adjustable gap protocol and most for the Side guard protocol....
-
Lavatories Adjacent to Partitions
Per 11B-606.2, we know that a clear space positioned for a forward approach is required (with exceptions), with proper knee and toe clearance. ...
-
502.3.4 Location
Access aisles shall be permitted to be placed on either side of the parking space except for angled van parking spaces which shall have access aisles located on the passenger side of the...
-
Size: ADA Standard Section 604.8.1.1
Section 604.8.1.1 covers the current ADA Standards for the size of wheelchair accessible compartments.
-
1010.1.6 Thresholds
In occupancy Group R-2 or R-3, threshold heights for sliding and side-hinged exterior doors shall be permitted to be up to 7¾ inches (197 mm) in height if all of the following apply:...
-
3.3.16 Door Use
The difference in rating was therefore more likely to have been influenced by the latch side clearance than door size, especially on the pull side....
-
Don-Jo Mfg., Inc. Vertical Rod Protector 83
Number 83 Description Latch Bolt Cover Width 6-3/4" Height 10" Projection 2-1/8" Material...
-
11B-705.1.2.2.2 Parallel curb ramps
Detectable warnings shall extend the full width of the turning space at the demarcation between the street and the sidewalk less 2 inches (sic) (51 mm) maximum on each side....
-
11B-902.2 Clear floor or ground space
Knee and toe clearance complying with Section 11B-306 shall be provided....
-
Obstructions
Obstructions “Obstructions” are also prohibited by TAS 604.3.2 within the required water closet clearance....
-
11B-902.2 Clear floor or ground space
Knee and toe clearance complying with Section 11B-306 shall be provided....
-
11B-902.2 Clear floor or ground space
Knee and toe clearance complying with Section 11B-306 shall be provided....
-
10 [§ 4.7.5]
10 [§ 4.7.5] Answer this question only if you skipped the previous two questions because the curb ramp you are surveying does not have flared sides....
-
608 Shower Compartments
Section 608 addresses transfer showers and roll-in showers and provides specifications for size and clearances, grab bars, seats, operable parts, shower spray units, thresholds, and enclosures...
-
Don-Jo Mfg., Inc. Vertical Rod Protector 81
Product Specifications Number 81 Description Latch Bolt Cover Width 6-3/4" Height 10" Projection 2-1...
-
Flush Controls [4.16.5]
Flush Controls [4.16.5] Flush valve controls must be mounted no more than 44 inches above the floor on the wide side of the toilet so that they are within reach from the available clear...
