For vertical supports, the MDE NPRM proposed that the bottom end of the support be 34 inches high minimum and 37 inches high maximum above the standing surface....
Search Results "Curb Ramp Bottom Landing"
Commonly Searched Documents
-
M305.3.2 Height (Section-by-Section Analysis)
-
Running Slope [1016.7.1]
To accommodate steep terrain, ORARs may be designed with shorter sections that have a steeper running slope and length, as shown in table 3, with resting intervals at the top and bottom...
-
1132A.9 Smooth surface
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal....
-
Mirrors [4.19.6]
The mounting height of the bottom of mirrors at accessible lavatories (40 inches maximum above the floor) is based on the standard eye level range of adults seated in wheelchairs (43 to...
-
4.34.6.7* OVENS
Bottom-hinged door...
-
Bathtub
As a result, grab bars that would permit older adults to raise and lower themselves from the bottom of the tub were not included in bathtub designs....
-
Appendix B Trails Study Participation Press Release
Appendix B Trails Study Participation Press Release National Center on Accessibility National Trails Surface Study Press Release NCA Seeks Land Managers with Trails to Participate...
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
Alterations
An accessible path of travel may consist of walkways, parking access aisles, curb ramps, regular ramps, doorways, paths through lobbies and corridors, elevators and lifts....
-
R409.10 Handrail Extensions
Handrail gripping surfaces shall extend beyond and in the same direction of ramp runs and stair flights in accordance with R409.10....
-
§ 38.25(c) Door height
For vehicles in excess of 22 feet in length, the overhead clearance between the top of the door opening and the raised lift platform, or highest point of a ramp, shall be a minimum of 68...
- Sargent NB8700 Top Latch Surface Vertical Rod Exit Device
-
Can parking signage height be considered a "safe harbor"?
The 2010 ADA Standards, Section 502.6 requires parking signage to be located 60” minimum AFF or AFG to the bottom of the sign. 2010 ADA Standards, “502.6 Identification....
-
1001.1 Scope
The requirements in 1011 through 1019 apply only to facilities constructed or altered by federal agencies or by non-federal entities on federal land on behalf of federal agencies pursuant...
-
410.6 Doors and Gates
EXCEPTION: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
1001.1 Scope
The requirements in 1011 through 1019 apply only to facilities constructed or altered by federal agencies or by non-federal entities on federal land on behalf of federal agencies pursuant...
-
Original research for ANSI A117.1 (1957 - 1961)
In the original research for ANSI A117.1 - 1961, American National Standard Specifications for Making Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps...
- Sargent AD8400 & NB-AD8400 Narrow Stile Concealed Vertical Rod Exit Device
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
The work to negotiate a ramp was linearly related to the angle of the ramp....
-
Examples of alternative ways to serve a customer when barrier removal is not feasible are:
Examples of alternative ways to serve a customer when barrier removal is not feasible are: At a dry cleaner's, providing curb-side service for a customer dropping off or picking up...
-
Handrails Requirement
Requirements for handrails in the proposed rule applied only to those provided along ramps and stairs....
- Increasing Opportunities for Access on the Appalachian Trail: A Design Guide
-
Future Work
Bars and the side guard were used often for repositioning the trunk and buttocks onto the platform after landing however their use for this purpose was not documented....