Knee and toe clearance complying with Section 11B-306 shall be provided....
Search Results "Door Maneuvering Clearance"
Filters
Commonly Searched Documents
-
11B-602.2 Clear floor space
-
CRL Jackson 1200 Series Push Pad Door Exit Devices
08 7100 CRL Jackson 20 Series Push Pad Door Exit Devices For 1-3/4" Narrow, Medium, and Wide Stile Aluminum, Wood or Hollow Metal Doors "Soft-Touch" Smooth Action Push-Pad Field...
-
HEWI Range 180 Glass Door Hardware
Real materials lend Range 180 enhanced value. The lever handles are made of solid stainless steel and can be optionally complemented with slate or glass elements. Range 180 includes...
-
602.2 Clear Floor Space
Knee and toe clearance complying with 306 shall be provided....
-
11B-602.2 Clear floor space
Knee and toe clearance complying with Section 11B-306 shall be provided....
-
11B-608.2.2.1 Clearance
A 36 inch (914 mm) wide minimum by 60 inch (1524 mm) long minimum clearance shall be provided adjacent to the open face of the shower compartment....
-
17. Maneuvering Clearances and Hardware
[See subsections ...]
-
BEST Door Lever Hardware Cylindrical Locks - 9K
The 9K Cylindrical Lock Offers Simple, Safe and Dependable Protection. The BEST 9K is the toughest cylindrical lock, built to deliver dependable use and superior security in a wide...
-
Wheelchair Accessible Gates
Web sites with designs that allow wheelchair access while restricting access by ATVs and motorcycles are listed near the end of this tech tip. The best Web site was that of Scottish...
-
10.4.1(5)
(5) Baggage check-in and retrieval systems shall be on an accessible route complying with 4.3, and shall have space immediately adjacent complying with 4.2.4. If unattended security...
-
4.1.6(3)(d)(i)
(i) Where it is technically infeasible to comply with clear opening width requirements of 4.13.5, a projection of 5/8 in maximum will be permitted for the latch side stop.
-
6.14.2 Gate Hardware
Gate hardware shall comply with operable controls requirements in ABAAS section 309.4 and 404.2.7.
-
General Elements
Most scoping provisions apply to both interior and exterior elements where provided throughout facilities and sites (and are not limited to those in corridors as shown here).
-
1133A.7, Item 3
3. A clear floor space shall not extend into the knee and toe space more than 19 inches (483 mm).
-
Grab Bars
Grab bars are usually provided in buildings to provide stability and allow people to use their arms to assist in movement over short distances. The most common location for grab bars...
-
1133A.7, Item 3
3. A clear floor space shall not extend into the knee and toe space more than 19 inches (483 mm).
-
§ 38.83(c)(8) Handrails
(8) Handrails. If provided, handrails shall allow persons with disabilities to grasp them from outside the vehicle while starting to board, and to continue to use them throughout the...
-
Cavity Sliders USA Inc. Wall Mount Track
CS Wall Mount Track is suitable for surface sliding applications where there is enough strength in the wall to mount and support a side-track with door above the opening....
-
7(1)(c)
(c) In U-shaped kitchens with sink or range or cooktop at the base of the "U", a 60-inch turning radius is provided to allow parallel approach, or base cabinets are removable at that...
-
Behavioral Safety Products #DH510 Mortise Ligature Resistant Integrated Door Lever
This unique mortise door latch innovatively integrates the lever handle and escutcheon, creating a superior design that is safe, easy to use and aesthetically pleasing....
-
11B-609.3 Spacing
The grab bar clearance of 1½ inches required in this section is a safety clearance to prevent injuries resulting from arms slipping through the openings....
-
11B-609.3 Spacing
The grab bar clearance of 1½ inches required in this section is a safety clearance to prevent injuries resulting from arms slipping through the openings....
