this code shall apply to the construction, alteration, relocation, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building...
Search Results "Building Permit"
-
[A] 101.2 Scope
-
Scoping [4.1.3(14)]
Scoping [4.1.3(14)] ADAAG requires both audible and visual alarms in facilities that have emergency warning systems whether building-wide systems or self-contained units are provided....
-
F208.3.1 General
Parking spaces complying with 502 that serve a particular building or facility shall be located on the shortest accessible route from parking to an entrance complying with F206.4....
-
11B-213.3 Plumbing fixtures and accessories
The 2016 California Plumbing Code (CPC), Table 422.1 provides minimum plumbing fixture requirements for new buildings, and changes of occupancy or use in an existing building resulting in...
-
11B-206.5.2 Rooms and spaces
Within a building or facility, every door, doorway or gate serving rooms and spaces complying with this chapter shall comply with Section 11B-404....
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
11B-213.3 Plumbing fixtures and accessories
The 2016 California Plumbing Code (CPC), Table 422.1 provides minimum plumbing fixture requirements for new buildings, and changes of occupancy or use in an existing building resulting in...
-
11B-206.5.2 Rooms and spaces
Within a building or facility, every door, doorway or gate serving rooms and spaces complying with this chapter shall comply with Section 11B-404....
-
221.1.1 Florida Vertical Accessibility
Nothing in this code relives the owner of any building, structure, or facility governed by this code from the duty to provide vertical accessibility to all levels above and below the occupiable...
-
§382.33(b)(5)
(5) Otherwise mandating separate treatment for passengers with a disability, unless permitted or required by this part or other applicable Federal requirements....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
§382.43(b)
(b) The requirements of paragraph (a) do not apply to you in any country in which the telecommunications infrastructure does not readily permit compliance....
-
M101.4 Equivalent Facilitation
The use of alternative designs or technologies that result in substantially equivalent or greater accessibility and usability than specified in the MDE Standards is permitted....
-
303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Figure 303.2 Vertical Change in Level...
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
Ramps
Slightly steeper running slopes are permitted for short ramps (maximum 6” rise) where space is limited (§405.2, Ex.)....
-
§ 38.77(a)
(a) Handrails and stanchions shall be sufficient to permit safe boarding, on-board circulation, seating and standing assistance, and alighting by persons with disabilities....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
407.3.3.2 Contact
The device shall not require physical contact to be activated, although contact is permitted to occur before the door reverses....
-
Addition
An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
Sec. 469.054(c)(3)
(3) the processing of an application for a variance from accessibility standards for a building or facility....
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions....