Yes No N/A Comments/Remedies B1 Is the vehicle pull-up space on a level surface, with slopes not exceeding 1:48 in all directions?...
Search Results "Kitchen Work Surface"
-
Section B: Passenger Drop-Off Area
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
Figure 505.4 Handrail Height – Drawing from the U.S. Access Board
-
Accessible Parking
Maintain curb ramps and sidewalks to prevent large cracks and uneven surfaces from forming....
-
Technical Memorandum TM 2013-23 Storage (Not in Kitchens or Kitchenettes)
comply with TAS 811 when storage is provided in all accessible spaces except kitchens and kitchenettes.* Based on Advisory 225.2 and input from the U.S....
-
Key Study findings:
When multiple transfers are required to reach higher or lower surfaces 15.2% of the participants in this study could not complete them at any height (11 out of 72 participants; 8 of which...
-
Sales and Service Counters, Teller Windows, Information Counters [7.2]
Sales and Service Counters, Teller Windows, Information Counters [7.2] ADAAG generally specifies accessible counter heights up to 34 inches [4.32] but allows a height up to 36...
-
1.1.7 Measurement of parking areas
1.1.7 Measurement of parking areas. Only accessible access aisles and passenger loading zones that are part of a larger parking area need to be measured. These areas should be...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance (§505.5, §505.7)
-
M305.3.1 Length (Section-by-Section Analysis)
In the MDE NPRM, the Access Board proposed a gripping surface length of four inches minimum for horizontal standing supports. No public comments were submitted on this requirement....
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
Objective Surface Measurements
Objective Surface Measurements For purposes of comparison, objective surface measurement data are included from the “Measurement of Surface Characteristics for Accessibility” NIH-funded...
-
Turning Space: ADA Standard Section 809.2.2
For example, in kitchens, 804.3.1 requires at least one work surface with clear floor space complying with 306 to be centered beneath....
-
4.32 SEATING, TABLES, AND WORK SURFACES
[See subsections ...]
-
A4.32 SEATING, TABLES, AND WORK SURFACES
[See subsections ...]
-
11B-809.12 Electrical receptacles, controls and switches
When the reach is over a kitchen work surface and base cabinet, the work surface shall be 36 inches (914 mm) maximum above the finish floor and 25 1/2 inches (650 mm) maximum in depth....
-
11B-809.12 Electrical receptacles, controls and switches
When the reach is over a kitchen work surface and base cabinet, the work surface shall be 36 inches (914 mm) maximum above the finish floor and 25 1/2 inches (650 mm) maximum in depth....
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
