Performance To resist both lever arm and torsion forces that constantly act upon any door, the 350/500 Heavy Wall Entrance features four Sigma deep penetration and filet welds plus mechanical...
Search Results "Electroacoustic Performance Standards"
Commonly Searched Documents
- Kawneer North America 350/500 Heavy Wall™ Entrances
- Rebuilding Together Oakland East Bay - Oakland, CA
- Allegion Falcon MA Series Mechanical Locks
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
Multiple Single-User Toilet Rooms
Where multiple single-user toilet rooms are clustered in a single location, fifty percent (50%), rather than the one hundred percent (100%) required by the 1991 Standards, are required to...
-
5.2.2.1 Transfer Surface Width Recommendations for M302
recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position as described in its proposed standard...
-
B.3.iv - Who makes the determination that a product meets equivalent facilitation?
The vendor may assert that its product meets or exceeds the level of accessibility required by a particular standard through equivalent facilitation....
-
24.1 Q. What types of grab bars should the reinforcement be designed to accommodate and what types may be used if the builder elects to install grab bars in some units at the time of construction?
In determining what is an appropriate grab bar, builders are encouraged to look to the 1986 ANSI A117.1 standard, the standard cited in the Fair Housing Act....
-
§ 36.304(d)(2)(iii)
., elements for which there are neither technical nor scoping specifications in the 1991 Standards), and therefore those elements must be modified to the extent readily achievable to comply...
-
Alterations and Additions
This guide provides an introduction to the scoping requirements that form the basis for the Department of Justice’s 2010 ADA Standards and the Department of Transportation's ADA Standards...
-
11B-202.3.1 Prohibited reduction in access
(c) If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical requirements or the...
-
2.2.3 Functional Reach
Data can be presented in 3-D, in the form of 2-D charts along key planes (e.g. sagittal plane to represent forward reach abilities), or described for a standard reach (e.g. maximum forward...
-
FOREWORD
Standards and policies are used to ensure and maximize the quality, objectivity, utility, and integrity of its information....
-
I. Executive Summary
in favor of expansive coverage, to the maximum extent permitted by the terms of the ADA; —that an impairment is a disability if it substantially limits the ability of an individual to perform...
-
E202.7 Best Meets
Where ICT conforming to one or more requirements in the Revised 508 Standards is not commercially available, the agency shall procure the ICT that best meets the Revised 508 Standards consistent...
-
M101.1 Purpose
The proposed standards contain technical criteria for medical diagnostic equipment that is accessible to and usable by patients with disabilities....
- US Business Leadership Network (USBLN)
-
11B-904.4.1 Parallel approach
[2010 ADA Standards] 904.4.1 Parallel Approach....
-
11B-604.4 Seats
[2010 ADA Standards] 604.4 Seats....
-
11B-502.5 Vertical clearance
[2010 ADA Standards] 502.5 Vertical Clearance....
- LaCantina Aluminum Wood Door System
-
Section 36.406(e) Housing at a Place of Education
standards....
-
Section 35.151(f) Housing at a place of education
standards....
-
R105.3 Undefined Terms
The meaning of terms not specifically defined in R105.5, the referenced standards, or regulations issued by Federal agencies that adopt this document as accessibility standards shall be...