Where separate court-floor holding cells are provided for adult male, juvenile male, adult female, or juvenile female, each courtroom shall be served by one cell of each type complying with...
Search Results "Shower Clear Floor Space"
Filters
Commonly Searched Documents
-
F231.3.2 Court-Floor Holding Cells
-
231.3.2 Court-Floor Holding Cells
Where separate court-floor holding cells are provided for adult male, juvenile male, adult female, or juvenile female, each courtroom shall be served by one cell of each type complying with...
-
703.5.9 Line Spacing
Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
Access Board: Accessible Bathing Facilities Scoping
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
703.2.8 Line Spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
Wheelchair Space
Space for a single wheelchair and its occupant....
-
Amusement Rides with Wheelchair Spaces
Amusement Rides with Wheelchair Spaces Minimum space requirements and clearances for wheelchairs are specified where a ride provides a wheelchair space....
-
Aluminum Flush Top SGF Series Pressure-Locked Grating
For those areas that receive a great deal of pedestrian traffic, our 1/4" opening 7-SGF-4 close space product is available which conforms with the provisions of the "Americans with Disabilities...
-
R309.2 Parallel Parking Spaces
R309.2 Parallel Parking Spaces. Parallel parking spaces shall comply with R309.2. Advisory R309.2 Parallel Parking Spaces....
-
R407.9.1 Extended Ramp Surface
R407.9.1 Extended Ramp Surface. The surface of the ramp run or landing shall extend 305 mm (1.0 ft) minimum beyond the inside face of a handrail complying with R409. Advisory...
-
Figure 302.3 Elongated Openings in Floor or Ground Surfaces – Drawing from the U.S. Access Board
-
3.13(d) Number of Wheelchair Spaces Required
Number of Wheelchair Spaces Required: Cinemark shall provide at least the minimum number of wheelchair spaces required in each auditorium as set forth in § 4.1.3(19)(a) of the Standards...
-
3. Measuring Door Openings
Measuring Door Openings Special care is needed when measuring the clear opening of a doorway. To measure the clear opening of a standard hinged door, open the door to 90 degrees....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
7(2)(a)
Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Cabinets under lavatories are acceptable provided the bathroom has space...
-
11B-304.3.2 T-Shaped space
The turning space shall be a T-shaped space within a 60 inch (1524 mm) square minimum with arms and base 36 inches (914 mm) wide minimum....
-
11B-206.4.1 Entrances
All entrances shall comply with Section 11B-404. [2010 ADA Standards] 206.4.1 Public Entrances. In addition to entrances required by 206.4.2 through 206.4.9, at least 60 percent...
-
C. Doors
Doors - Examine each of the interior routes described above: ...with the exception of doors at shallow closets, do the doors to required accessible spaces, and all doors into and within...
-
11B-812.6 Vehicle spaces
All vehicle spaces shall be marked to define their width....
-
Figure 11B-407.2.3.1 Floor designation
SECTION TITLE NOTES Figure 11B-407.2.3.1 Floor designation....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
