Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
Search Results "Practice Teeing Ground"
-
11B-306.3.2 Maximum depth
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-1008.2.5 Ramps
Within play areas, ramps connecting ground level play components and ramps connecting elevated play components shall comply with Section 11B-1008.2.5....
-
306.3.2 Maximum Depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground....
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
1008.2.5 Ramps
Within play areas, ramps connecting ground level play components and ramps connecting elevated play components shall comply with 1008.2.5....
-
Classroom Acoustics: ADA Standard Section 6.
Review the updated information on the revisions to the ADA Standards regarding classroom acoustics.
-
12203(a) Retaliation
.-- No person shall discriminate against any individual because such individual has opposed any act or practice made unlawful by this Act or because such individual made a charge, testified...
-
§27.11(c)(2)(iii)
(iii) Begin to modify, with official approval of recipient's management, any policies or practices that do not meet the requirements of this part according to a schedule or sequence that...
-
12203(a) Retaliation
(a) Retaliation No person shall discriminate against any individual because such individual has opposed any act or practice made unlawful by this chapter or because such individual made...
-
§35.150(d)(4)
plan requirement of a Federal agency regulation implementing section 504 of the Rehabilitation Act of 1973, then the requirements of this paragraph shall apply only to those policies and practices...
-
§100.500(a) Discriminatory effect
A practice has a discriminatory effect where it actually or predictably results in a disparate impact on a group of persons or creates, increases, reinforces, or perpetuates segregated housing...
-
§100.500(c)(2)
Once the charging party or plaintiff satisfies the burden of proof set forth in paragraph (c)(1) of this section, the respondent or defendant has the burden of proving that the challenged practice...
-
Food and Beverage Service
The Food Service: Accommodating Diners with Disabilities factsheet provides both legal standards and promising practices for paths of travel, approach to dining spaces, seating, dining...
-
APPENDIX D
PROPOSED ASTM INTERNATIONAL STANDARD Computing Pathway Roughness Index from Longitudinal Profile Measurements1 1This standard practice is under the jurisdiction of ASTM Committee...
-
§ 35.130(b)(7)(i)
(i) A public entity shall make reasonable modifications in policies, practices, or procedures when the modifications are necessary to avoid discrimination on the basis of disability, unless...
-
§ 35.136(i)(1) Reasonable modifications
A public entity shall make reasonable modifications in policies, practices, or procedures to permit the use of a miniature horse by an individual with a disability if the miniature horse...
-
§ 38.71(b)(2)
(2) Vehicles designed for, and operated on, pedestrian malls, city streets, or other areas where level boarding is not practicable shall provide wayside or car-borne lifts, mini-high platforms...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....