The fixture, without the optional -HSBJ hinged seat) shall withstand loads up to 2,000 pounds (907.1 kg) with no measurable deflections....
Search Results "Patient Seated in Wheelchair"
- Whitehall Mfg. WH2125A On-Floor Bariatric Stainless Steel Toilet
- Caroma® USA Invisi Series II Walvit Wall Hung Elongated Water Closet
-
Minimum Requirement
.); where fixed seating is provided and where there may be an audio-amplification system....
-
11B-604.8.1.4 Toe clearance
FIGURE 11B-604.8.1.4 WHEELCHAIR ACCESSIBLE TOILET COMPARTMENT TOE CLEARANCE...
-
Master Bedroom
Telephone which amplifies high frequencies which are lost by many older people Pull down upper closet rods to improve reach, especially for children, little people, and wheelchair...
-
15(d)
HWI shall ensure that each Post-1993 Owned Hotel and Post-1993 Joint Venture Hotel has one removable tub seat for each and every accessible tub room in the hotel that does not already have...
-
Performance Areas
Performance Areas An accessible route must connect stages and other performance areas directly to seating areas where they are directly connected by a circulation path as well as to...
-
608.5.2 Standard Roll-In Type Shower Compartments
Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from...
- Willoughby Industries ETW-1445-BS-HC Toilet for 45-degree Chase Wall
-
12162(a)(2)(B)(ii)
(ii) have space to park and secure a wheelchair;...
-
§ 38.107(b)
(b) Restrooms required to be accessible shall be in close proximity to at least one seating location for persons using mobility aids and shall be connected to such a space by an unobstructed...
-
8.2 READING AND STUDY AREAS
At least 5 percent or a minimum of one of each element of fixed seating, tables, or study carrels shall comply with 4.2 and 4.32....
-
11B-608.5.2 Standard roll-in type shower compartments
the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor...
-
11B-608.5.2 Standard roll-in type shower compartments
the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor...
-
8.2 Reading and Study Areas
At least 5 percent or a minimum of one of each element of fixed seating, tables, or study carrels shall comply with 4.2 and 4.32....
-
608.5.2 Standard Roll-In Type Shower Compartments
Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from...
-
SETTLEMENT AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND PALACE SPORTS AND ENTERTAINMENT, LLC, REGARDING THE PALACE OF AUBURN HILLS
[See subsections ...]
-
11B-608.5.2 Standard roll-in type shower compartments
) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor...
-
T207 Circulation Paths
As a matter of clarification, the proposed rule specified that, where doorways are provided on one side of a non-rail vehicle, an accessible circulation path must connect each wheelchair...
-
608.5.2 Standard Roll-In Type Shower Compartments
Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from...
-
11B-805.2.2 Beds
A 36 inch (914 mm) minimum wide clear space shall be provided along the full length of each side of the beds. [2010 ADAS] 805.3 Clear Floor or Ground Space. A clear floor space...
-
M305.3.2 Height
The height of gripping surfaces for standing supports shall be based on the position of the standing supports in relation to the standing surfaces they serve. Horizontal standing...
-
805.3 Clear Floor or Ground Space
A clear floor space complying with 305 shall be provided on each side of the bed. The clear floor space shall be positioned for parallel approach to the side of the bed.
-
M305.3.2 Height (Section-by-Section Analysis)
For horizontal supports, the MDE NPRM proposed a gripping surface height of 34 inches minimum and 38 inches maximum above the standing surface. There were no public comments on this...