Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
Search Results "Clearance in Base"
-
703.2.5 Character Height
-
Edge Protection
Toe clearance must be at least 30 inches wide and a minimum of 9 inches above the ground or deck surface beyond the railing....
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Forward Approach Manual Wheelchair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Forward Approach Scooter
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Forward Approach Power Chair
reaching over an obstruction in relation to the forward-most point, and the negative range implying that the reach target is brought closer to the person (such as on a table with knee clearance...
-
Landings [§405.7]
Handrails, edge protection, vertical posts and other elements cannot obstruct or overlap the minimum 60” by 60” clearance....
-
4) Medical or health care facilities
Required clearances in rooms exceed ADAAG requirements. No special, less stringent requirements for alterations (§6)....
-
226.1 General
However, employers should consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
Costs
Additional Costs Due to Final Rule Viewing Areas $2,176 for dual base binocular scopes and $3,380 for a dual base telescopes, if viewing scopes provided at viewing areas...
-
Brooks Equipment FIRETECH™ Fire Extinguisher Stand
Holds 5, 10, and 20 lb dry chemical extinguishers and features a large, sturdy base with molded-in handle for easy transport....
-
Just Manufacturing Classroom Concealed Ledgemount Teardrop Handle Faucet
Triple radius swing spout with 10" clearance. Heavey cast spout cone for added strength. Replaceable seats. Brass quarter turn stem units....
-
Just Manufacturing Concealed Classroom Faucet with Triple Radius Spout
Triple radius swing spout with 10" clearance. Heavey cast spout cone for added strength. Replaceable seats. Brass quarter turn stem units....
-
§382.3 Expected maximum flight duration
Expected maximum flight duration means the carrier's best estimate of the total duration of the flight from departure gate to arrival gate, including taxi time to and from the terminals, based...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
C. Housing In Residential Postsecondary Vocational Education Centers
Recipients must extend housing opportunities without discrimination based on race, color, national origin, sex, or handicap....
-
Equivalent Facilitation
The Department, in consultation with the Access Board, has granted equivalent facilitation for a design similar to the ADAAG specification but having a dome base diameter of 1.325mrn and...
-
§ 38.159(c)(1) Design load
shall support a load of 600 pounds (2665 N), placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches (660 mm by 660 mm), with a safety factor of at least 3 based...
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
American Safety Tread Co., Inc. Type T-24H Contrasting Stripe
Impact Resistant: These nosings are manufactured from an extruded aluminum base filled with a mixture of anti-slip abrasive granules in an advanced formula epoxy binder....
-
UNDUE HARDSHIP ISSUES
.(113) A determination of undue hardship should be based on several factors, including: the nature and cost of the accommodation needed; the overall financial resources...
-
Other international standards
Australian NATSPEC Reference Volume 1: Building Works, Concrete Finishes Section Three classes of surface finish based on using a straightedge method of testing: Class A...
-
Trail Type
Water Trail: A trail that has a surface consisting predominantly of water (but may include land-based portages) and that is designed and managed to accommodate use on that surface....
-
Magnuson Group FLAP Magazine & Literature Display
Frame is Silver Anodized Aluminum, shelves and base in Forged Grey or White Ral 9003....
