In each assembly area where audible communication is integral to the use of the space, an assistive listening system shall be provided....
Search Results "Work Area Equipment"
-
219.2 Required Systems
-
A4.33.7 Types of Listening Systems
with hearing aids not equipped with inductive pick-ups cannot use them without special receivers....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
5.8.2.1 Height of Breast Platform at Time of Measurement
This shape varies across different pieces of equipment, and breast platforms do not have standard features that can be used to define the required knee clearance space underneath the breast...
-
1. Width and Depth of Wheelchair Spaces
The MDE NPRM proposed to require diagnostic equipment to have a wheelchair space that is at least 36 inches wide (proposed M303.2.2)....
-
3(1)
(1) On accessible routes in public and common use areas, and for primary entry doors to covered units, doors that comply with ANSI 4.13 would meet this requirement....
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
219.2 Required Systems
In each assembly area where audible communication is integral to the use of the space, an assistive listening system shall be provided....
-
203.7 Detention and Correctional Facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
1007.7.1 Level of exit discharge
Where the exit discharge does not include an accessible route from an exit located on a level of exit discharge to a public way, an exterior area of assisted rescue shall be provided on...
-
1012.3 Other Vehicles
This section requires parking spaces for vehicles, other than recreational vehicles, to be 16 feet wide minimum to accommodate vans equipped with a lift or ramp....
-
Using a Fitness Center Does Not Have to be an Exercise in Frustration: Tips for People with Mobility and Visual Disabilities
Second Street, Pomona, CA 91766‑1854, Phone: (909) 469‑5380, TTY (909) 469-5520, Fax: (909) 469‑5503, Email: ahcs@westernu.edu, www.cdihp.org This work was partially supported by the...
-
Areas of Refuge [IBC §1007.6 (2003), §1003.2.13.5 (2000)]
Areas of refuge are fire-resistance rated and smoke protected areas where those unable to use stairs can register a call for evacuation assistance and await instructions or assistance....
- UpScale by Medical Accessibility - Adjustable Height Exam Table with Built-in Scale
-
M303.2.2 Width
Wheelchair spaces shall be 36 inches (915 mm) wide minimum. EXCEPTION: Wheelchair spaces located on raised platforms shall be permitted to be 32 inches (815 mm) wide minimum to a...
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.
-
M303.1 General (Section-by-Section Analysis)
This is an introductory section.
-
M303.2.4 Knee and Toe Clearance
Wheelchair spaces shall include knee and toe clearance complying with M303.2.4. The depth of the wheelchair space shall include knee and toe clearance of 17 inches (430 mm) minimum...
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.
-
10. Drinking fountains and water coolers
Accessible element or space ANSI A117.1 section APPLICATION 10. Drinking fountains and water coolers 4.15 Fifty percent of...