The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent materials...
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
1133A.4.1, Item 3
-
1133A.4.1, Item 3
The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent materials...
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
10.3.1(19)
Gates which must be pushed open by wheelchair or mobility aid users shall have a smooth continuous surface extending from 2 inches above the floor to 27 inches above the floor....
-
Precision Safe Sidewalks LLC Sidewalk Trip Hazard Repair Service
Our patented saw-cutting technology completely and cleanly removes trip hazards from sidewalks, virtually eliminating claims that result from trips and falls on uneven sidewalk. By...
-
Bosch 3 Point Self Leveling Alignment Laser Level GPL 3 S
-- Recalibration Wrench, (3) -- AA 1.5V Batteries, (1) -- Mounting Strap, (1) - Belt Pouch Benefits Three-point plumb and level point projection — accurately transfers...
-
Behavioral Safety Products #BF920 Suicide Resistant Attenda Desk
This unit is manufactured in the USA to ISO Quality Standards, and it’s slightly textured maintenance-free surface is stain resistant and easy to clean. ...
-
1013.3 Slope
The slope of the surface of tent pads, tent platforms, and clear ground spaces shall not be steeper than 1:48 in any direction....
-
1013.3 Slope
The slope of the surface of tent pads, tent platforms, and clear ground spaces shall not be steeper than 1:48 in any direction....
-
Playground Study Site
A transfer point/platform was incorporated in the climbing structure; however, the surface leading to it was fine beach sand. Total fall height was determined to be 3.1 m (10 ft)....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
Populas Vox Corner Office Workstation
Also available with a single surface....
-
5.6.1 Stirrups Provision for M301
5.6.1 Stirrups Provision for M301 NPRM Description: For patients with limited leg strength and control, thigh, knee and calf supports are necessary to maintain an appropriate...
-
4.27.3* Height
The highest operable part of controls, dispensers, receptacles, and other operable equipment shall be placed within at least one of the reach ranges specified in 4.2.5 and 4.2.6....
-
4.31.3* Mounting Height
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6.
-
4.34.3(3) Forward and Parallel Approach
(3) Forward and Parallel Approach. If both a forward and parallel approach are possible, operable parts of controls shall be placed within at least one of the reach ranges in...
-
Allowances for Typical Roadway Geometry
for Typical Roadway Geometry The 1991 ADAAG and 2004 ADA and ABA Accessibility Guidelines specify a maximum running slope of 5 percent and maximum cross slope of 2 percent for walking surfaces...
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
4.8.5* HANDRAILS
If a ramp run has a rise greater than 6 in (250 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
-
505.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2....
