Commenters also opposed specific recognition of "high-low" units as an alternative to two separate units since other types, such as single bowl units with two spouts, are commercially available...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
Two Drinking Fountains
-
AJW Architectural Products U134EA 33 fl oz. Automatic Liquid Soap Dispenser - Surface Mounted
A pre-measured amount of soap will dispense. Unit is operated by three (3) "C" batteries, not provided, Alkaline batteries are recommended for best performance....
-
Whitehall Mfg. WH2125A On-Floor Bariatric Stainless Steel Toilet
The unit is fabricated of 14 gage, type 304 stainless steel and is seamless welded construction. The exterior and bowl interior has a satin finish....
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
Press Release
Press Release The parties to this Settlement Agreement are the United States of America and the City of Isle of Palms, South Carolina....
-
Press Release
Press Release The parties to this Settlement Agreement are the United States of America and the City of Vero Beach, Florida....
-
5.1.2 Transfer Surface High Height
The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.34.5.2(2)
(2) The height of the water closet shall be at least 15 in (380 mm), and no more than 19 in (485 mm), measured to the top of the toilet seat....
-
§ 37.155(a)(1)
(1) Effects on current fixed route service, including reallocation of accessible fixed route vehicles and potential reduction in service, measured by service miles;...
-
Seating Locations
Remember, when measuring the accessible route through the space, measure the aisle width as if the chairs are pulled out and occupied....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
13 [§ 4.7.10]
When taking this measurement, the measuring tape should be aligned parallel to the ramp run itself and should stretch from the intersection of the ramp and gutter to the innermost edge of...
-
M304.2.1 Slip Resistant (Section-by-Section Analysis)
One manufacturer commented on this requirement, requesting that the rule provide clarification on how to define or measure a standing surface as “slip resistant.”...
-
E102.8 TIA (Section-by-Section Analysis)
TIA 1083 (2007), Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, would be incorporated by reference at 410.4.2....
-
C102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
10.2.1(1)
new bus stop pads are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96 inches (measured...
-
E102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
602.2 Clear Floor Space
Units shall have a clear floor or ground space complying with 305 positioned for a forward approach and centered on the unit....
-
§ 38.179(b)
(b) Each tractor unit which accommodates passengers and each trailer unit shall comply with §38.25 and §38.29 of this part....
-
602.2 Clear Floor Space
Units shall have a clear floor or ground space complying with 305 positioned for a forward approach and centered on the unit....
-
11B-602.2 Clear floor space
Units shall have a clear floor or ground space complying with Section 11B-305 positioned for a forward approach and centered on the unit....
