EV chargers shall be adjacent to, and within the projected width of, the vehicle space being served....
Search Results "Ramp Width"
Filters
Commonly Searched Documents
-
11B-812.10.4 Location
-
Site Arrival Points: ADA Standard Section 206.2.1
Section 206.2.1 covers the scoping requirements for site arrival points of accessible routes in the most current ADA Standards.
-
11B-1002.4.3 Gaps
Exception: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
A4.13.9 Door Hardware
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) from its bottom edge and be centered across the width of the door....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
Armor-Tile Tactile Systems Surface Applied Systems
adhesive, fasteners, sealant beveled edges for smooth transition meeting ADA requirements light weight and easy to handle easily cut to conform to angled and radius ramps...
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. ...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
R409.3 Continuity
Handrails shall be continuous within the full length of each ramp run or stair flight....
-
Appendix B: Overview of Federal Regulations and Guidance for Detectable Warnings
The ADAAG requires detectable warnings on the full surface of curb ramps. In 1994 the USDOJ, USDOT, and U.S....
-
1. Thigh Breadth
Thigh Breadth Thigh breadth was used to provide an estimate of the width of the seating surface....
-
1012.1 General
The technical requirements address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
