Latch-side clearance not only provides proper positioning at door hardware but also facilitates proceeding through doors against the force of closers....
Search Results "Non-Positive Shut Off"
Commonly Searched Documents
-
Is latch-side maneuvering clearance as specified in the Standards applicable to doors with panic bars?
-
§ 38.159(b)(2)(ii) Exception
., “rotary lift”), the requirements of this paragraph (b)(2) prohibiting the lift from being stowed while occupied shall not apply if the stowed position is within the passenger compartment...
-
11B-813.2.10 Door swing
A door, in any position, shall be permitted to encroach into the turning space by 12 inches (305 mm) maximum....
-
11B-904.4.1 Parallel approach
A clear floor or ground space complying with Section 11B-305 shall be positioned for a parallel approach adjacent to the 36 inch (914 mm) minimum length of counter....
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
A negative example is shown in slide 3, left photo; a positive example is shown in slide 3, right photo....
-
404.2.9 Door and Gate Opening Force
These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position....
-
11B-604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
11B-904.4.1 Parallel approach
A clear floor or ground space complying with Section 11B-305 shall be positioned for a parallel approach adjacent to the 36 inch (914 mm) minimum length of counter....
-
11B-604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
Architect
The 4040XP provides adjustments for Position 1-6, has a range of interior and exterior door sizes it can work on....
-
25. RESERVATIONS SYSTEM
(e) HWI’s policy shall be that in assigning guestrooms upon check-in, each Brand Hotel shall hold available at least two non-premium accessible rooms for guests requesting accessible rooms...
- Merlexi Craft™ Liberty MRI Wheelchairs
- BEA Inc. LZR-Microscan Swinging Door Sensor
-
212 and 606 Kitchens, Kitchenettes, Lavatories, and Sinks
The 1991 Standards, at section 4.24, and the 2010 Standards, at section 606, both require the clear floor space at sinks to be positioned for a forward approach and knee and toe clearance...
- indoo.rs® Indoor Navigation Solution App
-
11B-804.6.6 Refrigerator/freezer
The clear floor or ground space shall be positioned for a parallel approach to the space dedicated to a refrigerator/freezer with the centerline of the clear floor or ground space offset...
-
§382.133(f)
paragraphs (f)(1) through (7) of this section upon inquiry from an individual concerning the use in the cabin during air transportation on such a flight of a ventilator, respirator, continuous positive...
-
Imaging equipment with bores
using magnets, x-rays, or detectors into which a patient and the table on which the patient lies is inserted into the equipment through a cylindrical opening (bore) in order to achieve the positioning...
-
1630.10 Qualification standards, tests, and other selection criteria
class of individuals with disabilities, on the basis of disability, unless the standard, test or other selection criteria, as used by the covered entity, is shown to be job-related for the position...
-
Q: Can a PSAP dedicate a separate seven-digit line for TTY calls?
A: Yes, but TTY users must also have direct, equal access to all call-taking positions on 9-1-1 lines....
-
11B-608.5 Controls
ETA Editor's Note At each accessible shower type, the 2013 CBC requirements for positioning controls are more restrictive than 2010 ADAS....
-
1011.4.2 Wheelchair Space
Wheelchair spaces shall be positioned for a forward approach to the table and provide knee and toe clearance complying with 306 under the table....
-
804.6.6 Refrigerator/Freezer
The clear floor or ground space shall be positioned for a parallel approach to the space dedicated to a refrigerator/freezer with the centerline of the clear floor or ground space offset...
-
407.8 Reach Height and Depth
At least one of each type of operable part of stationary ICT shall be at a height conforming to 407.8.2 or 407.8.3 according to its position established by the vertical reference plane specified...