Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impact Performance Phase 2: Final Report REPORT PREPARED FOR: U.S ACCESS BOARD, WASHINGTON,...
Search Results "Surface Slope"
-
Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report
-
What other surface considerations affect wheelchair travel?
In addition to slip resistance requirements, wheelchair users are affected by the rolling resistance of the surface of the floor and--on exterior surfaces--by cross slope....
-
Attachment J
All spaces and access aisles for persons with disabilities shall be flat and level, with slopes and cross-slopes not exceeding 1:50 in all directions, and their surfaces shall be firm, stable...
-
11B-405.7.1 Slope
Exception: Slopes not steeper than 1:48 shall be permitted....
-
11B-405.7.1 Slope
Exception: Slopes not steeper than 1:48 shall be permitted....
-
11B-405.7.1 Slope
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
U.S. Forest Service Accessible Picnic Table Designs - Steel Leg Picnic Table
-
U.S. Forest Service Accessible Picnic Table Designs - Wood Picnic Table
-
U.S. Forest Service Accessible Picnic Table Designs - Stone Leg Picnic Table
-
The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report REPORT PREPARED FOR: U.S. ACCESS BOARD, WASHINGTON, DC Authors: Alicia Koontz, PhD,...
-
Slope Game: Dive Into the Pulse of Neon Speed
Slope Game is an endless 3D runner where you guide a rolling ball down a never-ending slope suspended in a neon-lit void....
-
B. M301 Diagnostic Equipment Used by Patients in a Supine, Prone, or Side-lying Position and M302 Diagnostic Equipment Used by Patients in a Seated Position
Therefore, the Significant Changes Section addresses the transfer surface and lift compatibility requirements for M301 and M302 together....
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
5.4.1 Transfer Support Location for M301 and M302
Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
-
TotTurf® Synthetic Grass: Play Spaces
Description Tot Turf Play Spaces is a line of natural looking, soft, attenuating turf surfacing perfect for playgrounds....
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
Handrails [§405.8, §505]
Handrail Height and Clearance Handrail Continuity and Extensions Surface requirements and clearances facilitate a power grip along the length of handrails....
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Slope 2 - Endless Speed and Reflex Challenge
Slope 2 is an adrenaline-pumping arcade game that keeps players on edge from start to finish....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
