The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
Filters
Commonly Searched Documents
-
610.3.2 L-Shaped Seats
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
Free-Standing Overhead Lifts
Free-standing, nonpermanent overhead track lifts are a good solution when the provider does not want the lift to be permanently installed or where the existing ceiling structure cannot support...
-
References
Technical Report (AMRL-TR−74‒102) (AD A025 240). Aerospace Medical Research Laboratory, Wright-Patterson Air Force Base, OH....
-
4.1.4 OCCUPANCY CLASSIFICATIONS
Buildings and facilities shall comply with these standards to the extent noted in this section for various occupancy classifications, unless otherwise modified by a special application section...
-
§ 38.171(b)
(b) If portions of the vehicle or conveyance are modified in a way that affects or could affect accessibility, each such portion shall comply, to the extent practicable, with the applicable...
-
Landscape Forms Inc. Redline Bench Collection
With Redline, he set out "to deconstruct the bench and approach it with a different structural attitude."...
-
Landscape Forms Inc. Kaleidoscope OS Transportation Stop Shelters
Kaleidoscope OS (Open Structure) creates outdoor structures of exceptional utility, stability and style....
-
Sec.36.304(a) General
A public accommodation shall remove architectural barriers in existing facilities, including communication barriers that are structural in nature, where such removal is readily achievable...
-
§ 36.304(a) General
A public accommodation shall remove architectural barriers in existing facilities, including communication barriers that are structural in nature, where such removal is readily achievable...
-
4.34.5.5(3) Grab bars
Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 49....
-
4.26.3(3)
induced in a fastener or mounting device from the application of 250 lbf (1112N) shall be less than the allowable lateral load of either the fastener or mounting device or the supporting structure...
-
4.1.4(9) INSTITUTIONAL
Institutional occupancy includes, among others, the use of a building or structure, or any portion thereof, in which people have physical or medical treatment or care, or in which the liberty...
-
4.34.5.4(3) Grab bars
Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 48....
-
Forward Approach: ADA Standard Section 904.4.2
A portion of the counter surface that is 30 inches (760 mm) long minimum and 36 inches (915 mm) high maximum shall be provided....
-
11B-1008.4.4 Entry points and seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (279 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
11B-813 Adult changing facilities
However, the absence of scoping or technical requirements in the Standards would make it difficult to conclude what that means....
-
610.3.2 L-Shaped Seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
11B-203 General exceptions
Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by 11B-203. 11B-203.9 Employee work areas....
-
12209(b)(2)(C)
Representatives as an exercise of the rulemaking power of the House of Representatives, with full recognition of the right of the House to change its rules, in the same manner, and to the same extent...
-
1.1.3.2, Item 1
State-owned buildings, including buildings constructed by the Trustees of the California State University, and to the extent permitted by California laws, buildings designed and constructed...
-
§35.176 Alternative means of dispute resolution
Where appropriate and to the extent authorized by law, the use of alternative means of dispute resolution, including settlement negotiations, conciliation, facilitation, mediation, factfinding...
-
220 and 707 Automatic Teller Machines and Fare Machines
220 and 707 Automatic Teller Machines and Fare Machines Section 707 of the 2010 Standards adds specific technical requirements for speech output, privacy, tactilely-discernible input...
