Surfaces of transfer walls shall not be sharp and shall have rounded edges....
Search Results "Surface Slope"
-
11B-1009.4.4 Surface
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment
The transfer or positioning support should be oriented horizontally on imaging equipment with transfer surfaces....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
405.7.1 Slope
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
405.7.1 Slope
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Figure 505.7.2 Handrail Non-Circular Cross Section – Drawing from the U.S. Access Board
-
M301.2.3 Size
The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides....
-
Stabila slope meter is easy to read
I like this slope meter because of the readings provided on the top and the side of the slope meter. Makes documentation with photos very easy in the field....
-
4.7.9.1 General
Where utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent, but not less than one in each accessible space,...
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
M301.3.1 Transfer Supports
A.1) A transfer support will extend horizontally along the side of the patient scanning/imaging table at least the minimum width of the transfer surface, but in all cases a 28 inches minimum...
-
Adjustable Height Range Considered
to make up the difference between the two surfaces, in one direction or the other....
-
5.3.2 Transfer Sides Recommendations for M301
the long side of the surface....
-
Play Areas
Word Fillable Form (0.4MB) Word Non-Fillable Form (0.3MB) PDF Non-Fillable Form (0.3MB)
-
Permitted Means of Pool Access
Permitted Means of Pool Access Pool Type Sloped Entry Lift Transfer Walls Transfer Systems Stairs Swimming (less than 300 linear...
-
1(2) Site impracticality
(2) Site impracticality. Covered multifamily dwellings with elevators shall be designed and constructed to provide at least one accessible entrance on an accessible route, regardless...
-
12.2 Q. What happens if a builder deliberately manipulates the grade so that a second story, which also might have been treated as a ground floor, requires steps?
A. Deliberate manipulation of the height of the finished floor level to avoid the requirements of the Fair Housing Act would serve as a basis for the Department to determine that...
-
1. Standing Supports
The proposed rule included a provision requiring standing supports on each side of the standing surface and compliance with the technical requirements for standing supports in proposed M305.3...
-
5.4.2.1 Transfer Support Length for Stretchers
5.4.2.1 Transfer Support Length for Stretchers. Transfer supports on stretchers should be a minimum of 15 inches long.
-
Visual Detection of Detectable Warning Materials by Pedestrians with Visual Impairments - Final Report
(Task Order 18 under Project DTFH61-01-C-00049) Authors: James Jenness & Jeremiah Singer May 24, 2006 Prepared for: Federal Highway Administration Washington,...
